General Description
The SX1213 is a low cost single-chip receiver operating in the frequency ranges from 300MHz to 510MHz. The SX1213 is optimized for very low power consumption (3mA). It incorporates a baseband demodulator with data rates up to 200 kb/s. Data handling features include a sixty-four byte FIFO, packet handling, CRC and data whitening processing. Its highly integrated architecture allows for minimum external component count whilst maintaining design flexibility. All major RF communication parameters are programmable and most of them may be dynamically set. It complies with European (ETSI EN 300-220 V2.1.1) and North American (FCC part 15.247 and 15.249) regulatory standards.

Features
*Low Rx power consumption: 3mA
*Good reception sensitivity: down to -104 dBm at 25 kb/s in FSK, -110 dBm at 2kb/s in OOK
*Packet handling feature with data whitening and CRC processing
*RSSI (Received Signal Strength Indicator) range from Rx noise floor to 0 dBm
*Bit rates up to 200 kb/s, NRZ coding
*On-chip frequency synthesizer
*FSK and OOK modulation
*Incoming sync word recognition
*Built-in Bit-Synchronizer for incoming data and clock synchronization and recovery
*5 x 5 mm TQFN package
*Optimized Circuit Configuration for Low-cost applications
*Pin to pin compatible with SX1212 Transceiver

Applications
*Wireless alarm and security systems
*Wireless sensor networks
*Automated Meter Reading
*Home and building automation
*Industrial monitoring and control
*Remote Wireless Control

SX1213IWLTRT

Trackback :: http://datasheetblog.com/trackback/2844

댓글을 달아 주세요 Comment

GENERAL DESCRIPTION
The SX1223 is a single chip transmitter operating in UHF frequency bands including the 434, 869 and 915 MHz license-free ISM (Industrial Scientific and Medical) bands. Its highly integrated architecture allows for minimum external components while maintaining design flexibility. All major RF communication parameters are programmable and most of them can be set dynamically. The SX1223 offers the advantage of high data rate communication at rates of up to 153.6 kbit/s. The SX1223 is optimized for low cost applications while offering high RF output power. The device is suitable for applications which have to satisfy either the European (ETSI-300-220) or the North American (FCC part 15) regulatory standards.

KEY PRODUCT FEATURES
*RF output power: up to +10 dBm
*Low power consumption: TX = 25.8 mA @ 10 dBm (typical)
*Supply voltage down to 2.0 V
*Data rate from 1.2 to 153.6 kbit/s
*On-chip frequency synthesizer
*Continuous phase 2-level FSK modulation
*Very small RoHS green package (TQFN24, 4mm x 4mm)

APPLICATIONS
*Automated Meter Reading (AMR)
*Home Automation and Access Control
*High-Quality Speech, Music and Data over RF

SX1223I073TRT

Trackback :: http://datasheetblog.com/trackback/2509

댓글을 달아 주세요 Comment

GENERAL DESCRIPTION
The XE1205 is an integrated transceiver operating in the 433, 868 and 915 MHz license-free ISM (Industrial, Scientific and Medical) frequency bands; it can also address other frequency bands in the 180-1000 MHz range. Its highly integrated architecture allows for minimum external components while maintaining design flexibility. All major RF communication parameters are programmable and most of them can be dynamically set. The XE1205 offers the unique advantage of narrow-band and wide-band communication, this without the need to modify the number or parameters of the external components.
The XE1205 is optimized for low power consumption while offering high RF output power and channelized operation suited for both the European (ETSI EN 300-220-1) and the North merican (FCC part 15) regulatory standards. TrueRF™ technology enables a low-cost external component count (elimination of the SAW filter) whilst still satisfying ETSI and FCC regulations.

KEY PRODUCT FEATURES
*Programmable RF output power: up to +15 dBm
*High Rx sensitivity: down to -121 dBm at 1.2 kbit/s, -116 dBm at 4.8 kbits.
*Low power: RX=14 mA; TX = 62 mA @ 15 dBm
*Can accommodate 300-1000 MHz frequency range
*Wide band operation: up to 304.7 kbit/s, NRZ coding
*Narrow band operation: 25 kHz channels for data rates up to 4.8 kbit/s, NRZ coding; optional transmitter pre-filtering to enable adjacent channel power below -37 dBm at 25 kHz
*On-chip frequency synthesizer with minimum frequency resolution of 500 Hz
*Continuous phase 2-level FSK modulation
*Incoming data pattern recognition
*Built-in Bit-Synchronizer for incoming data and clock synchronization and recovery
*FEI (Frequency Error Indicator) with built-in AFC
*RSSI (Received Signal Strength Indicator)
*16-byte FIFO for transmit / receive data buffering and transfer via SPI bus

APPLICATIONS
*Narrow-band and wide-band security systems
*Voice and data over an RF link
*Process and building control
*Access control
*Home automation
*Home appliances interconnection

XE1205I074TRLF

Trackback :: http://datasheetblog.com/trackback/2378

댓글을 달아 주세요 Comment

Features
• Integrated PLL Loop Filter
• ESD Protection (4 kV HBM/200V MM; Except Pin 2: 4 kV HBM/100V MM) also at ANT1/ANT2
• High Output Power (8.0 dBm) with Low Supply Current (9.0 mA)
• Modulation Scheme ASK/FSK
– FSK Modulation is Achieved by Connecting an Additional Capacitor Between the XTAL Load Capacitor and the Open Drain Output of the Modulating Microcontroller
• Easy to Design-in Due to Excellent Isolation of the PLL from the PA and Power Supply
• Single Li-cell for Power Supply
• Supply Voltage 2.0V to 4.0V in the Temperature Range of –40°C to +85°C
• Package TSSOP8L
• Single-ended Antenna Output with High Efficient Power Amplifier
• CLK Output for Clocking the Microcontroller
• One-chip Solution with Minimum External Circuitry

 Applications
• Industrial/Aftermarket Remote Keyless Entry Systems
• Alarm, Telemetering, and Energy Metering Systems
• Remote Control Systems for Consumer and Industrial Markets
• Access Control Systems
• Home Automation
• Home Entertainment
• Toys

1. Description
The ATA8401 is a PLL transmitter IC, which has been developed for the demands of RF low-cost transmission systems for industrial applications at data rates up to 50 kBaud ASK and 32 kBaud FSK modulation scheme. The transmitting frequency range is 310 MHz to 350 MHz. It can be used in both FSK and ASK systems.

Trackback :: http://datasheetblog.com/trackback/673

댓글을 달아 주세요 Comment

Features
• Transparent RF Receiver ICs for 315 MHz (ATA8201) and 433.92 MHz (ATA8202) With
High Receiving Sensitivity
• Fully Integrated PLL With Low Phase Noise VCO, PLL, and Loop Filter
• High FSK/ASK Sensitivity:–105 dBm (ATA8201, FSK, 9.6 Kbits/s, Manchester, BER 10-3)
–114 dBm (ATA8201, ASK, 2.4 Kbits/s, Manchester, BER 10-3)
–104 dBm (ATA8202, FSK, 9.6 Kbits/s, Manchester, BER 10-3)
–113 dBm (ATA8202, ASK, 2.4 Kbits/s, Manchester, BER 10-3)
• Supply Current: 6.5 mA in Active Mode (3V, 25°C, ASK Mode)
• Data Rate: 1 Kbit/s to 10 Kbits/s Manchester ASK, 1 Kbit/s to 20 Kbits/s Manchester
FSK With Four Programmable Bit Rate Ranges
• Switching Between Modulation Types ASK/FSK and Different Data Rates Possible in
≤ 1 ms Typically, Without Hardware Modification on Board to Allow Different Modulation Schemes
• Low Standby Current: 50 µA at 3V, 25°C
• ASK/FSK Receiver Uses a Low-IF Architecture With High Selectivity, Blocking, and Low Intermodulation (Typical 3-dB Blocking 68.0 dBC at ±3 MHz/74.0 dBC at ±20.0 MHz, System I1dBCP = –31 dBm/System IIP3 = –24 dBm)
• Telegram Pause Up to 52 ms Supported in ASK Mode
• Wide Bandwidth AGC to Handle Large Out-of-band Blockers above the System I1dBCP
• 440-kHz IF Frequency With 30-dB Image Rejection and 420-kHz IF Bandwidth to Support PLL Transmitters With Standard Crystals or SAW-based Transmitters
• RSSI (Received Signal Strength Indicator) With Output Signal Dynamic Range of 65 dB
• Low In-band Sensitivity Change of Typically ±2.0 dB Within ±160-kHz Center Frequency Change in the Complete Temperature and Supply Voltage Range
• Sophisticated Threshold Control and Quasi-peak Detector Circuit in the Data Slicer
• Fast and Stable XTO Start-up Circuit (> –1.4 kΩ Worst-case Start Impedance)
• Clock Generation for Microcontroller
• ESD Protection at all Pins (±4 kV HBM, ±200V MM, ±500V FCDM)
• Dual Supply Voltage Range: 2.7V to 3.3V or 4.5V to 5.5V
• Temperature Range: –40°C to +85°C
• Small 5 mm × 5 mm QFN24 Package

Applications
• Industrial/Aftermarket Keyless Entry and Tire Pressure Monitoring Systems
• Alarm, Telemetering and Energy Metering Systems
• Remote Conrol Systems for Consumer and Industrial Markets
• Access Control Systems
• Home Automation
• Home Entertainment
• Toys

ATA8201
ATA8202
TAG Receiver, UHF

Trackback :: http://datasheetblog.com/trackback/672

댓글을 달아 주세요 Comment

FEATURES
• Meets EPCGlobal™ Gen2 (v. 1.0.9) and ISO/IEC 18000-6C
• 860 ~ 960 MHz Global Operating Frequency
• Supports Optional Gen2 Commands: Block Write and Block Erase
• 192-bit memory: 96-bit Electronic Product Code (EPC™), 32-bit Access Password, 32- bit KILL Password, 32-bit TID memory (Factory Programmed and Locked)
• Designed for High-performance, Low Power Consumption based on most Advanced Silicon Process Node for RFID (130 nm)
• Fast tag Singulation using most Advanced Anti-Collision Scheme
• Suitable for H-field and E-field operation
• RoHS Compliant

APPLICATIONS
• Supply Chain Management & Distribution Logistics
• Express Parcel Delivery
• Airline Baggage Handling
• Asset Tagging

DESCRIPTION
 Large retailers have issued mandates to their suppliers to ship cases and pallets of goods/products with RFID Smart Labels attached. TI’s Gen2 Straps are intended to simplify the manufacture of inlays for conversion into Smart Labels for various applications. The Straps are based on the EPCGlobal™ Gen2 specification (v. 1.0.9) and ISO/IEC 18000-6C
 TI’s Gen2 Straps operate with extremely low power and yet provide long read and write ranges, fast data transfer and high Smart Label throughput. A detailed description of the command set, memory and operation of the Strap is given in the UHF Gen2 Protocol reference Guide literature number 11-09-21-700)
TAG STRAP, UHF

Trackback :: http://datasheetblog.com/trackback/602

댓글을 달아 주세요 Comment