General Description
The XP1035-BD is a linear power amplifier that operates over the 5.9-9.5GHz frequency band. The device provides 26 dB gain and 39 dBm Output Third Order Intercept Point (OIP3) across the band and is comprised of a three stage power amplifier with an integrated, temperature compensated on-chip power detector. The device includes on-chip ESD protection structures and DC by-pass capacitors to ease the implementation and volume assembly of the part. The
device is manufactured in 0.5um GaAs PHEMT device technology with BCB wafer coating to enhance ruggedness and repeatability of performance. The XP1035-BD is well suited for Point-to-Point Radio, LMDS, SATCOM and VSAT applications.

Features
*26 dB Small Signal Gain
*39 dBm Third Order Intercept Point (OIP3)
*Integrated Power Detector
*100% On-Wafer RF Testing

Trackback :: http://datasheetblog.com/trackback/2076

댓글을 달아 주세요 Comment

Description
The LTC®1481 is an ultralow power differential line transceiver designed for data transmission standard RS485 applications. It will also meet the requirements of RS422.
The CMOS design offers significant power savings over its bipolar counterparts without sacrificing ruggedness against overload or ESD damage. Typical quiescent current is only
80mA while operating and less than 1mA in shutdown.
The driver and receiver feature three-state outputs, with the driver outputs maintaining high impedance over the entire common mode range. Excessive power dissipation caused by bus contention or faults is prevented by a thermal shutdown circuit which forces the driver outputs into a high impedance state. The receiver has a fail-safe feature which guarantees a high output state when the inputs are left open.
The LTC1481 is fully specified over the commercial and extended industrial temperature range and is available in 8-pin PDIP and SO packages.

Features
*Low Power: ICC = 120mA Max with Driver Disabled
*Drivers/Receivers Have ±10kV ESD Protection
*1mA Quiescent Current in Shutdown Mode
*High Speed: Up to 2.5Mbits/s Data Rate
*ICC = 500mA Max with Driver Enabled, No Load
*Single 5V Supply
*–7V to 12V Common Mode Range Permits ±7V Ground Difference Between Devices on the Data Line
*Thermal Shutdown Protection
*Power Up/Down Glitch-Free Driver Outputs Permit Live Insertion or Removal of Transceiver
*Driver Maintains High Impedance in Three-State or with the Power Off
*Up to 32 Transceivers on the Bus
*30ns Typical Driver Propagation Delays with 5ns Skew
*Pin Compatible with the LTC485

Applications
*Battery-Powered RS485/RS422 Applications
*Low Power RS485/RS422 Transceiver
*Level Translator

LTC1481CN8, LTC1481IN8, LTC1481CS8, LTC1481IS8

Trackback :: http://datasheetblog.com/trackback/2069

댓글을 달아 주세요 Comment

Description
Clare and IXYS have combined to bring OptoMOS® technology, reliability and compact size to a new family of High Power Solid State Relays. As part of this new family, the CPC1786 single pole normally open (1-Form-A) DC Solid State Relay employs optically coupled MOSFET technology to provide 2500Vrms of input to output isolation.
The output is constructed with an efficient MOSFET switch and photovoltaic die that uses Clare’s patented OptoMOS architecture while the input GaAlAs infrared LED provides the optically coupled control. The combination of low on-resistance and high load current handling capability makes this relay suitable for a variety of high-performance DC switching applications.
The unique i4-PAC package pioneered by IXYS allows solid state relays to achieve the highest load current and power ratings. This package features an IXYS unique process where the silicon chips are soft soldered onto the Direct Copper Bond (DCB) substrate instead of the usual copper leadframe. The DCB ceramic, the same substrate used in high power modules, not only provides 2500Vrms isolation but also very low thermal resistance (0.35°C/W).

Features
*100% Solid State
*Compact i4-PAC™ Power Package
*Low Thermal Resistance (0.35°C/W)
*1.75ADC Load Current with 5ºC/W Heat Sink
*Electrically Non-conductive Thermal Pad for Heat Sink Applications
*No Moving Parts
*Low Drive Power Requirements
*Arc-Free With No Snubbing Circuits
*2500Vrms Input/Output Isolation
*No EMI/RFI Generation
*Machine Insertable, Wave Solderable

Applications
*Industrial Controls
*Motor Control
*Robotics
*Medical Equipment—Patient/Equipment Isolation
*Instrumentation
*Multiplexers
*Data Acquisition
*Electronic Switching
*I/O Subsystems
*Meters (Watt-Hour, Water, Gas)
*Transportation Equipment
*Aerospace/Defense

CPC1786J
TAG Power, Relay

Trackback :: http://datasheetblog.com/trackback/1951

댓글을 달아 주세요 Comment

Description
The ADNS-3040 is an ultra low-power optical navigation sensor.
It has a new, lowpower architecture and automatic power management modes, making it ideal for battery-and power-sensitive applications such as cordless input devices.
The ADNS-3040 is capable of high-speed motion detection – up to 20 ips and 8G.
In addition, it has an on-chip oscillator and LED driver to minimize external components.
The ADNS-3040 along with the ADNS-3120-001 lens, ADNS- 2220 clip and HLMP-ED80-
PS000 LED form a complete and compact mouse tracking system.
There are no moving parts, which means high reliability and less maintenance for the end user.
In addition, precision optical alignment is not required, facilitating high volume assembly.
The sensor is programmed via registers through a four-wire serial port. It is packaged in a
20-pin DIP.

Features
* Low power architecture
* Self-adjusting power-saving modes for longest battery life
* High speed motion detection up to 20 ips and 8G
* SmartSpeed self-adjusting frame rate for optimum performance
* Motion detect pin output
* Internal oscillator – no clock input needed
* Selectable 400 and 800 cpi resolution
* Wide operating voltage: 2.5V-3.6V nominal
* Four wire serial port
* Minimal number of passive components

Applications
* Optical Mice
* Optical trackballs
* Integrated input devices
* Battery-powered input devices

ADNS3040

Trackback :: http://datasheetblog.com/trackback/1821

댓글을 달아 주세요 Comment

General Description
The AAT4901 FastSwitch™ is a member of AnalogicTech’s Application Specific Power MOSFET™ (ASPM™) product family.
It is a full-bridge buffered power stage operating with an input voltage range of 2.0V to 5.5V.
The device is designed to operate with a switching frequency of up to 2MHz, minimizing the cost and size of external components.
The AAT4901 is protected from shoot-through current by integrated break-before-make circuitry. The drivers can be independently controlled and their propagation delay, from input to output, is typically between 8ns-19ns dependent upon logic option.
Four options are offered providing a single input control, dual input control or as two independent half-bridges.
Other features include low RDS(ON) and low quiescent current allowing for high efficiency performance.
The AAT4901 is available in the space-saving, Pb-free 8-pin SC70JW package and is rated over the -40°C to +85°C temperature range.


Features
* VIN Range: 2.0V–5.5V
* RDS(ON):
- High-side 220mΩ
- Low-side 160mΩ
* Break-Before-Make Shoot–Through Protection
* 4 Options
- Single Control Input with Enable
* Two Logic Versions
- Dual Control Input with Brake Function
- Dual Half-bridge
* Low Quiescent Current:
- 10μA (max) DC
- 4mA (max) at 1MHz
* -40°C to +85°C Temperature Range
* SC70JW-8 Package

Applications
* DC Motor Drive
* Door Locks
* Dual Low-Side MOSFET Gate Driver
* Fan Motors
* High Frequency DC/DC Converters
* High Speed Line Drive
* Proximity Detectors


AAT4901IJS-1-T1
AAT4901IJS-2-T1
AAT4901IJS-3-T1
AAT4901IJS-4-T1
TAG Bridge, Power

Trackback :: http://datasheetblog.com/trackback/1820

댓글을 달아 주세요 Comment

General Description
 The AP393A consists of two independent precision voltage comparators with an offset voltage specification as low as 8.0mV max for two comparators which were designed specifically to operate from a single power supply over a wide range of voltages.
Operation from split power supplies is also possible and the low power supply current drain is independent of the magnitude of the power supply voltage.
These comparators also have a unique characteristic in that the input common-mode voltage range includes ground, even though operated from a single power supply voltage.
Application areas include limit comparators, simple analog to digital converters; pulse, square wave and time delay generators; wide range VCO; MOS clock timers; multivibrators and high voltage digital logic gates.
The AP393A is designed to directly interface with TTL and CMOS.
When operated from both plus and minus power supplies, the AP393A will directly interface with MOS logic where their low power drain is a distinct advantage over standard comparators.

Features
* Wide supply
  Voltage range: 2.0V to 36V
  Single or dual supplies: ±1.0V to ±18V
* Very low supply current drain (0.4mA) – independent of supply voltage
* Low input biasing current: 150nA
* Low input offset current: ±70nA
* Low input offset voltage: ±4mV
* Input common-mode voltage range includes ground
* Differential input voltage range equal to the power supply voltage
* Low output saturation voltage: 250mV at 4mA
* Output voltage compatible with TTL, DTL, ECL, MOS and CMOS logic systems
* MSOP-8L and SOP-8L: Available in “Green” Molding Compound (No Br, Sb)
* Lead Free Finish/ RoHS Compliant (Note 1)

Applications
* High precision comparators
* Reduced VOS drift over temperature
* Eliminates need for dual supplies
* Allows sensing near ground
* Compatible with all forms of logic
* Power drain suitable for battery operation

AP393AM8G-U
AP393AM8G-13
AP393ASG-U
AP393ASG-13

Trackback :: http://datasheetblog.com/trackback/1754

댓글을 달아 주세요 Comment

Description
Clare and IXYS have combined to bring OptoMOS®technology, reliability and compact size to a new family of high-power Solid State Relays.
As part of this family, the CPC1908 single pole normally open (1-Form-A) Solid State Power Relay is rated for up to 8.5Arms continuous load current with a 5°C/W heat sink.
The CPC1908 employs optically coupled MOSFET technology to provide 2500Vrms of input to output isolation.
The output is constructed with efficient MOSFET switches and photovoltaic die that use Clare’s patented OptoMOS architecture while the input, a highly efficient GaAlAs infrared LED provides
the optically coupled control.
The combination of low on-resistance and high load current handling capability makes this relay suitable for a variety of high performance switching applications.
The unique i4-PAC package pioneered by IXYS allows Solid State Relays to achieve the highest load current and power ratings.
This package features a unique IXYS process where the silicon chips are soft soldered onto the Direct Copper Bond (DCB) substrate instead of the traditional copper leadframe.
The DCB ceramic, the same substrate used in high power modules, not only provides 2500Vrms isolation but also very low thermal resistance (0.35 °C/W).

Features
* Compact i4-PAC™ Power Package
* Low Thermal Resistance (0.35 °C/W)
* 8.5Arms Load Current with 5°C/W Heat Sink
* Electrically Non-conductive Thermal Pad for Heat Sink Applications
* Low Drive Power Requirements
* Arc-Free With No Snubbing Circuits
* 2500Vrms Input/Output Isolation
* No EMI/RFI Generation
* Machine Insertable, Wave Solderable

Applications
* Industrial Controls
* Motor Control
* Robotics
* Medical Equipment—Patient/Equipment Isolation
* Instrumentation
- Multiplexers
- Data Acquisition
- Electronic Switching
- I/O Subsystems
- Meters (Watt-Hour, Water, Gas)
* Transportation Equipment
* Aerospace/Defense

CPC1908J

TAG Power

Trackback :: http://datasheetblog.com/trackback/1730

댓글을 달아 주세요 Comment

General Description
The AAT4672 SmartSwitch™ is a member of AnalogicTech’s Application Specific Power Management IC™ family.
This device is a dual input, single output power supply selector switch, designed to operate from USB ports, AC adapter inputs, batteries, or any other power supply with an input voltage up to 6V.
The AAT4672 connects the supply on the MAIN pin to the OUT pin through a very low on-resistance power MOSFET when the device is enabled, the MAIN pin voltage is higher than the under voltage lockout (UVLO) threshold, and MAIN pin voltage is greater than the AUX pin voltage plus 200mV.
The AUX pin connects to the OUT pin only when the MAIN pin voltage drops 0.2V below the AUX pin voltage and the AUX pin voltage is greater than the UVLO threshold.
If both input supplies (MAIN/AUX) are below the UVLO threshold, then the OUT pin floats.
The two internal power switches are current limited and the thresholds can be programmed through resistors on the IMAIN and IAUX pins respectively.
A power level selection pin, PWRSEL, is provided to toggle the AUX current limit between 100% and 20% of the current limit setting programmed by the resistor on the IAUX pin.
This is particularly useful for USB applications where the power supply can be powered by either a 500mA or a 100mA USB port.
The AAT4672 is available in a thermally enhanced, space-saving, Pb-free 12-pin TSOPJW package and is specified for operation over the -40°C to +85°C temperature range.

Features
* Input Voltage Supply Range: 2.5V to 6V
* High Level of Integration:
- Reverse Blocking Diode
- Current Sensing
- Programmable Current Limiting
- Automatic Power Supply Switching
* Break-Before-Make Switch-Over
- Minimum Output Voltage Drop During Change-Over
* Shutdown Current < 1μA
* Thermal Protection
* TSOPJW-12 Package

Applications
* Bluetooth™ Headsets
* Cell Phones
* Digital Still Cameras
* MP3 Players
* Personal Data Assistants (PDAs)

AAT4672ITP-T1

Trackback :: http://datasheetblog.com/trackback/1707

댓글을 달아 주세요 Comment

Description
The CS5460 is a highly integrated ΔΣ Analog-to-Digital Converter (ADC) which combines two ΔΣ ADCs, high speed power calculation functions, and a serial interface on a single chip.
It is designed to accurately measure and calculate: Energy, Instantaneous Power, IRMS, and
VRMS for single phase 2 or 3-wire power meter applications.
The CS5460 interfaces to a low cost shunt or transformer to measure current, and resistive divider or transformer to measure voltage.
The CS5460 features a bi-directional serial interface for communication with a micro-controller and a fixed-width programmable frequency output that is proportional to energy.
The product is initialized and fully functional upon power-up, and includes facilities for system-level calibration under control of the user program.

Features
*Energy Data Linearity: 0.1% of Reading over 1000:1 Dynamic Range
*On-Chip Functions: Energy, I ∗ V, IRMS and VRMS, Energy to Pulse-Rate Conversion
*Complies with IEC 687/1036, JIS
*Power Consumption <12 mW
*Interface Optimized for Shunt Sensor
*Phase Compensation
*Ground-Referenced Signals with Single Supply
*System Calibration
*On-chip 2.5 V Reference (60 ppm/°C drift)
*Simple Three-wire Serial Interface
*Watch Dog Timer
*Power Supply Monitor
*Power Supply Configurations
- VA+ = +5 V; VA- = 0V; VD+ = +3 V to +5 V
- VA+ = +2.5 V; VA- = -2.5 V; VD+ = +3 V

CS5460-BS
TAG Energy, ic, Power

Trackback :: http://datasheetblog.com/trackback/1692

댓글을 달아 주세요 Comment

GENERAL DESCRIPTION
 The patent-pending ACT8798 is a complete, costeffective, highly-efficient ActivePMUTM power management solution that is ideal for a wide range of portable handheld equipment.
This device integrates three step-down DC/DC converters and three low dropout linear regulators (LDOs) into a single, thin, space-saving package. An I2C Serial Interface provides programmability for the DC/DC converters and LDOs.
REG1, REG2 and REG3 are fixed-frequency, current-mode PWM step-down DC/DC converters that are optimized for high efficiency and are capable of supplying up to 1.2A, 1.2A and 750mA, respectively.
REG4, REG5 and REG6 are low noise, high PSRR linear regulators that are capable of supplying up to 250mA each.
The ACT8798 is available in a tiny 4mm x 4mm 24-pin Thin-QFN package that is just 0.75mm thin.

FEATURES
* Multiple Patents Pending
* Six Integrated Regulators
- 1.2A PWM Step-Down DC/DC
- 1.2A PWM Step-Down DC/DC
- 750mA PWM Step-Down DC/DC
- 250mA Low Noise LDO
- 250mA Low Noise LDO
- 250mA Low Noise LDO
* I2CTM Compatible Serial Interface
- Programmable Output Voltages
- Configurable Operating Modes
* Minimal External Components
* 4x4mm, Thin-QFN (TQFN44-24) Package
- Only 0.75mm Height
- RoHS Compliant

APPLICATIONS
* Portable Devices and PDAs
* Wireless Handhelds
* DMB Enabled Devices
* GPS Receivers, etc.

Trackback :: http://datasheetblog.com/trackback/1668

댓글을 달아 주세요 Comment