General Description
The ICS1892, an enhanced version of the ICS 1890, is a fully integrated, physical-layer device (PHY) that is compliant with both the 10Base-T and 100Base-TX CSMA/CD Ethernet Standard, ISO/IEC 8802-3.
The ICS1892 incorporates digital signal processing (DSP) in its Physical Medium Dependent (PMD) sublayer. As a result, it can transmit and receive data on unshielded twisted-pair (UTP) category 5 cable with attenuation in excess of 24 dB at 100 MHz. With this ICS-patented technology, the ICS1892 can virtually eliminate errors from killer packets.
The ICS1892 supports a broad range of applications: data terminal equipment (network interface cards and motherboards), switches, repeaters, bridges, and routers. Its Media Independent Interface (MII) supports direct chip-to-chip and motherboard-to-daughterboard connections as well as connections to an MII connector and cable. The ICS1892 also provides a Serial Management Interface for exchanging command and status information with a Station Management (STA) entity.
The ICS1892 Media Dependent Interface (MDI) can be configured to provide either half- or full-duplex operation at data rates of 10 MHz or 100 MHz. The MDI configuration can be done manually (with input pins or control register settings) or automatically (using the Auto-Negotiation features). When the ICS1892 Auto-Negotiation sublayer is enabled, it exchanges technology capability data with its remote l ink partner and automatically selects the highest-performance operating mode they have in common.

Features
*Supports category 5 cables with attenuation in excess of 24 dB at 100 MHz across a temperature range from -5° to +85° C
*DSP-based baseline wander correction to virtually eliminate killer packets across temperature range of from -5° to +85° C
*Low-power, 0.5-micron CMOS
*Single 5.0-V power supply.
*Single-chip, fully integrated PHY provides PCS, PMA, PMD, and AUTONEG sublayers of IEEE standard
*10Base-T and 100Base-TX IEEE 802.3 compliant
*Fully integrated, DSP-based PMD includes:
–Adaptive equalization and baseline wander correction
–Transmit wave shaping and stream cipher scrambler
–MLT-3 encoder and NRZ/NRZI encoder
*Highly configurable design supports:
–Node, repeater, and switch applications
–Managed and unmanaged applications
–10M or 100M half- and full-duplex modes
–Parallel detection
–Auto-negotiation, with Next Page capabilities
*MAC/Repeater Interface can be configured as:
–10M or 100M Media Independent Interface
–100M Symbol Interface (bypasses the PCS)
–10M 7-wire Serial Interface
*Provides Loopback Modes for Diagnostic Functions
*Small Footprint 64-pin Low-Profile LQFP and MQFP packages available

ICS1892Y, ICS1892Y-10, ICS1892Y-14

Trackback :: http://datasheetblog.com/trackback/2417

댓글을 달아 주세요 Comment

General
The ICS1893CY-10 is a low-power, physical-layer device (PHY) that supports the ISO/IEC 10Base-T and 100Base-TX Carrier-Sense Multiple Access/Collision Detection (CSMA/CD) Ethernet standards. The ICS1893CY-10 supports managed or unmanaged node, repeater, and
switch applications.
The ICS1893CY-10 is intended for MII, Node applications that require the Auto-MIDIX feature that automatically corrects crossover errors in plant wiring.
The ICS1893CY-10 incorporates digital signal processing (DSP) in its Physical Medium Dependent (PMD) sublayer.
As a result, it can transmit and receive data on unshielded twisted-pair (UTP) category 5 cables with attenuation in excess of 24 dB at 100 MHz. With this ICS-patented technology, the ICS1893CY-10 can virtually eliminate errors from killer packets.
The ICS1893CY-10 provides a Serial Management Interface for exchanging command and status information with a Station Management (STA) entity.
The ICS1893CY-10 Media Dependent Interface (MDI) can be configured to provide either half- or full-duplex operation at data rates of 10 MHz or 100 MHz. The MDI configuration can be established manually (with input pins or control register settings) or automati c a l l y (using the
Auto-Negotiation features). When the ICS1893CY-10 Auto-Negotiation sublayer is enabled, it exchanges  technology capability data with its remote link partner and automatically selects the highest-performance operating mode they have in common.

Features
• Supports category 5 cables with attenuation in excess of 24 dB at 100 MHz
• Fully integrated, DSP-based PMD includes:
– Adaptive equalization and baseline wander correction
– Transmit wave shaping and stream cipher scrambler
– MLT-3 encoder and NRZ/NRZI encoder
• Low-power, 0.35-micron CMOS (typically 400 mW)
• Power-down mode typically 21mW
• Single 3.3-V power supply.
• Single-chip, fully integrated PHY provides PCS, PMA, PMD, and AUTONEG sublayers of IEEE standard
• 10Base-T and 100Base-TX IEEE 802.3 compliant
• Highly configurable design supports:
– Node, repeater, and switch applications
– Managed and unmanaged applications
– 10M or 100M half- and full-duplex modes
– Parallel detection
– Auto-negotiation, with Next Page capabilities
– Auto-MDI/MDIX crossover correction
• MAC/Repeater Interface can be configured as:
– 10M or 100M Media Independent Interface
– 100M Symbol Interface (bypasses the PCS)
– 10M 7-wire Serial Interface
• Clock and crystal supported
• Small Footprint 64-pin Thin Quad Flat Pack (TQFP)
• Available in Industrial Temperature and Lead-Free

ICS1893CY-10
ICS1893CYI-10
ICS1893CY-10LF
ICS1893CYI-10LF
TAG PHYCEIVER

Trackback :: http://datasheetblog.com/trackback/965

댓글을 달아 주세요 Comment

1. Features
The Realtek RTL8201BL is a Fast Ethernet Phyceiver with selectable MII or SNI interface to the MAC chip. It provides the following features:
TAG PHYCEIVER

Trackback :: http://datasheetblog.com/trackback/351

댓글을 달아 주세요 Comment