General Description
The SX1213 is a low cost single-chip receiver operating in the frequency ranges from 300MHz to 510MHz. The SX1213 is optimized for very low power consumption (3mA). It incorporates a baseband demodulator with data rates up to 200 kb/s. Data handling features include a sixty-four byte FIFO, packet handling, CRC and data whitening processing. Its highly integrated architecture allows for minimum external component count whilst maintaining design flexibility. All major RF communication parameters are programmable and most of them may be dynamically set. It complies with European (ETSI EN 300-220 V2.1.1) and North American (FCC part 15.247 and 15.249) regulatory standards.

Features
*Low Rx power consumption: 3mA
*Good reception sensitivity: down to -104 dBm at 25 kb/s in FSK, -110 dBm at 2kb/s in OOK
*Packet handling feature with data whitening and CRC processing
*RSSI (Received Signal Strength Indicator) range from Rx noise floor to 0 dBm
*Bit rates up to 200 kb/s, NRZ coding
*On-chip frequency synthesizer
*FSK and OOK modulation
*Incoming sync word recognition
*Built-in Bit-Synchronizer for incoming data and clock synchronization and recovery
*5 x 5 mm TQFN package
*Optimized Circuit Configuration for Low-cost applications
*Pin to pin compatible with SX1212 Transceiver

Applications
*Wireless alarm and security systems
*Wireless sensor networks
*Automated Meter Reading
*Home and building automation
*Industrial monitoring and control
*Remote Wireless Control

SX1213IWLTRT

Description
The ATR2732N1 is a front-end monolithic integrated circuit, manufactured using Atmel®’s silicon-germanium BiCMOS process (SiGMOS).
The ATR2732N1 carries out all functions of RF and IF processing, as well as the clock-signal generation for these functions. Therefore, there is an integrated fractional PLL, which, equivalent to most of the other functions, can be controlled via an external digital bus. The RF functions include LNA, down-conversion mixing, amplifying, detection, and gain control. An external SAW filter is required in the signal path after the RF functions. Additional amplifiers with detection and control functions are integrated IF functions.
The device offers several tuning support functions, and was created to simplify the design and manufacturing process. To this end, the number of external components are minimal.
The part fits perfectly to Atmel’s DAB baseband processor ATR2740.

Features
*ATR2732N1 is a Special Version of ATR2732 Recommended for Automotive Applications
*Highly Integrated DAB Front-end Solution Covering Band III and L-band Reception
*Convenient Internal Clock Generation, Single Reference Clock
*Fractional PLL for VHF
*Fully Integrated VCOs
*High-precision Digitally Tunable Reference Oscillator
*Integrated High-performance LNAs
*Very Flexible Programming of the AGC
*Automatically Aligned External Filter Tuning
*Simple Three-wire Digital Control Interface for Easy Handling
*Single Low Voltage (3.3V) Supply Operation
*Low Current Consumption Due to Several Power-down Options
*Small SMD Package (QFN 9 mm × 9 mm)

Applications
*Commercial DAB Receivers
*DAB Receiver Solutions for Car Radio Applications
*Portable DAB Solutions

ATR2732N1-PBQW, ATR2732N1-PBPW

Description
The ATR2732N3 is a front-end monolithic integrated circuit, manufactured using Atmel®’s silicon-germanium BiCMOS process (SiGMOS).
The ATR2732N3 carries out all functions of RF and IF processing, as well as the clock-signal generation for these functions. Therefore, there is an integrated fractional PLL, which, equivalent to most of the other functions, can be controlled via an external digital bus. The RF functions include LNA, down-conversion mixing, amplifying, detection, and gain control. An external SAW filter is required in the signal path after the RF functions. Additional amplifiers with detection and control functions are integrated IF functions.
The device offers several tuning support functions, and was created to simplify the design and manufacturing process. To this end, the number of external components are minimal.
The part fits perfectly to Atmel’s DAB baseband processor ATR2740.

Features
*Highly Integrated DAB Front-end Solution Covering Band III and L-band Reception
*Convenient Internal Clock Generation, Single Reference Clock
*Fractional PLL for VHF
*Fully Integrated VCOs
*High-precision Digitally Tunable Reference Oscillator
*Integrated High-performance LNAs
*Very Flexible Programming of the AGC
*Automatically Aligned External Filter Tuning
*Simple Three-wire Digital Control Interface for Easy Handling
*Single Low Voltage (3.3V) Supply Operation
*Low Current Consumption Due to Several Power-down Options
*Small SMD Package (QFN 9 mm × 9 mm)

Applications
*Commercial DAB Receivers
*DAB Receiver Solutions for Car Radio Applications
*Portable DAB Solutions

ATR2732N3-PBQW, ATR2732N3-PBPW

General Description
The ICS1892, an enhanced version of the ICS 1890, is a fully integrated, physical-layer device (PHY) that is compliant with both the 10Base-T and 100Base-TX CSMA/CD Ethernet Standard, ISO/IEC 8802-3.
The ICS1892 incorporates digital signal processing (DSP) in its Physical Medium Dependent (PMD) sublayer. As a result, it can transmit and receive data on unshielded twisted-pair (UTP) category 5 cable with attenuation in excess of 24 dB at 100 MHz. With this ICS-patented technology, the ICS1892 can virtually eliminate errors from killer packets.
The ICS1892 supports a broad range of applications: data terminal equipment (network interface cards and motherboards), switches, repeaters, bridges, and routers. Its Media Independent Interface (MII) supports direct chip-to-chip and motherboard-to-daughterboard connections as well as connections to an MII connector and cable. The ICS1892 also provides a Serial Management Interface for exchanging command and status information with a Station Management (STA) entity.
The ICS1892 Media Dependent Interface (MDI) can be configured to provide either half- or full-duplex operation at data rates of 10 MHz or 100 MHz. The MDI configuration can be done manually (with input pins or control register settings) or automatically (using the Auto-Negotiation features). When the ICS1892 Auto-Negotiation sublayer is enabled, it exchanges technology capability data with its remote l ink partner and automatically selects the highest-performance operating mode they have in common.

Features
*Supports category 5 cables with attenuation in excess of 24 dB at 100 MHz across a temperature range from -5° to +85° C
*DSP-based baseline wander correction to virtually eliminate killer packets across temperature range of from -5° to +85° C
*Low-power, 0.5-micron CMOS
*Single 5.0-V power supply.
*Single-chip, fully integrated PHY provides PCS, PMA, PMD, and AUTONEG sublayers of IEEE standard
*10Base-T and 100Base-TX IEEE 802.3 compliant
*Fully integrated, DSP-based PMD includes:
–Adaptive equalization and baseline wander correction
–Transmit wave shaping and stream cipher scrambler
–MLT-3 encoder and NRZ/NRZI encoder
*Highly configurable design supports:
–Node, repeater, and switch applications
–Managed and unmanaged applications
–10M or 100M half- and full-duplex modes
–Parallel detection
–Auto-negotiation, with Next Page capabilities
*MAC/Repeater Interface can be configured as:
–10M or 100M Media Independent Interface
–100M Symbol Interface (bypasses the PCS)
–10M 7-wire Serial Interface
*Provides Loopback Modes for Diagnostic Functions
*Small Footprint 64-pin Low-Profile LQFP and MQFP packages available

ICS1892Y, ICS1892Y-10, ICS1892Y-14

Product Overview
TRC101 is a highly integrated single chip, zero-IF, multi-channel, low power RF transceiver. It is an ideal fit for low cost, high volume, two way short-range wireless applications for use in the unlicensed 300-1000 MHz frequency bands. All critical RF and baseband functions are completely integrated in the chip, thus minimizing external component count and simplifying and speeding design-ins. Use of a low cost, generic 10MHz crystal and a low-cost microcontroller is all that is needed to create a complete link. The TRC101 also incorporates different sleep modes to reduce overall current consumption and extend battery life. Its small size with low power consumption makes it ideal for various short range radio applications.

Key Features
*Modulation: FSK (Frequency Hopping Spread Spectrum capability)
*Frequency range: 300-1000 MHz
*High sensitivity: (-105 dBm)
*High data rate: Up to 256 kbps
*Low current consumption (RX current ~8.5mA)
*Wide operating supply voltage: 2.2 to 5.4V
*Low standby current (0.2uA)
*Integrated PLL, IF, Baseband Circuitry
*Automatic Frequency Adjust(TX/RX frequency alignment)
*Programmable Analog/Digital Baseband Filter
*Programmable Output RF Power
*Programmable Input LNA Gain
*Internal Valid Data Recognition
*Transmit/Receive FIFO
*Standard SPI Interface
*TTL/CMOS Compatible I/O pins
*Programmable CLK Output Freq
*Automatic Antenna tuning circuit
*Low cost, generic 10MHz Xtal reference
*Integrated, Programmable Low Battery Voltage Detector
*Programmable Wake-up Timer with programmable Duty Cycle
*Integrated Selectable Analog/Digital RSSI
*Integrated Crystal Oscillator
*External Processor Interrupt pin
*Programmable Crystal Load Capacitance
*Programmable Data Rate
*Integrated Clock & Data Recovery
*Programmable, Positive/Negative FSK Deviation
*External Wake-up Events
*Support for Multiple Channels
-[315/433 Bands] 380 Channels(25kHz)
-[868 Band] 761 Channels(25kHz)
-[915 Band] 1040 Channels(25kHz)
*Power-saving sleep mode
*Very few external components requirement
*Small size plastic package: 16-pin TSSOP
*Standard 13 inch reel, 2000 pieces.

Popular applications
*Active RFID tags
*Automated Meter reading
*Home & Industrial Automation
*Security systems
*Two way Remote keyless entry
*Automobile Immobilizers
*Sports & Performance monitoring
*Wireless Toys
*Medical equipment
*Low power two way telemetry systems
*Wireless mesh sensors
*Wireless modules

GENERAL DESCRIPTION
The ADF4350 allows implementation of fractional-N or integer-N phase-locked loop (PLL) frequency synthesizers if used with an external loop filter and external reference frequency.
The ADF4350 has an integrated voltage controlled oscillator (VCO) with a fundamental output frequency ranging from 2200 MHz to 4400 MHz. In addition, divide-by-1/2/4/8 or 16 circuits allow the user to generate RF output frequencies as low as 137.5 MHz. For applications that require isolation, the RF output stage can be muted. The mute function is both pin- and software-controllable. An auxiliary RF output is also available, which can be powered down if not in use.
Control of all the on-chip registers is through a simple 3-wire interface. The device operates with a power supply ranging from 3.0 V to 3.6 V and can be powered down when not in use.

FEATURES
*Output frequency range: 137.5 MHz to 4400 MHz
*Fractional-N synthesizer and integer-N synthesizer
*Low phase noise VCO
*Programmable divide-by-1/-2/-4/-8/-16 output
*Typical rms jitter: 0.5 ps rms
*Power supply: 3.0 V to 3.6 V
*Logic compatibility: 1.8 V
*Programmable dual-modulus prescaler of 4/5 or 8/9
*Programmable output power level
*RF output mute function
*3-wire serial interface
*Analog and digital lock detect
*Switched bandwidth fast-lock mode
*Cycle slip reduction

APPLICATIONS
*Wireless infrastructure (W-CDMA, TD-SCDMA, WiMAX, GSM, PCS, DCS, DECT)
*Test equipment
*Wireless LANs, CATV equipment
*Clock generation

ADF4350BCPZ, ADF4350BCPZ-RL, ADF4350BCPZ-RL7, EVAL-ADF4350EB1Z

General Description
The XPIO™ 110GXS is a fully integrated 10 Gbps serializer/deserializer device designed for high-speed switches and routers that require very low power budget and a small footprint as well. Centering on 10 Gbps speed, the XPIO 110GXS is a versatile chip that is capable of handling applications in various standards, such as OC-192 (9.95 Gbps) and 10GE (10.31 Gbps).
An on-chip low jitter PLL generates all required clocks based on an external reference clock at 1/16 or 1/64 frequency of the serial data rate, which is 622.08 MHz or 155.52 MHz, respectively, for OC-192 applications. An Integrated Limiting Amplifier allows flexibility in placement and reduced bit-error rates (BER).
Fabricated with state-of-the-art CMOS technology, the XPIO 110GXS performs all necessary functions for serial-to-parallel and parallel-to-serial conversions, and consumes less than one third of the power consumed by the more conventional SiGe Bi-CMOS designs.

Features
*Single chip SERDES solution with integrated transmitter and receiver
*Continuous serial operation range from 9.95 Gbps to 10.31 Gbps
*Parallel LVDS data range from 622 Mbps to 644 Mbps
*Low power consumption (800 mW typical)
*Performs 16:1 serialization and 1:16 deserialization
*Embedded Limiting Amplifier enhances receiver sensitivity
*Low-jitter PLL for clock generation
*On-chip Clock Data Recovery circuit
*On-chip FIFO to decouple transmit clocks
*Bit order swap for 10GE operations
*Programmable 4-phase LVDS clock output for easy system design
*Repeating serial data output
*Line loopback, diagnostic loopback, and simultaneous loopback modes
*Frequency Lock Alarm Output
*Programmable differential output swing on both Serial driver and Parallel LVDS driver
*1.3V core voltage and 2.5V I/O voltage
*Supports 10GE (10-Gigabit Ethernet), OC-192, XFP, XSBI and SFI-4.1 interfaces
*269-pin flip-chip BGA (15 x 15 mm body size, 0.8 mm pitch)
*-40 to 85°C operating temperature

LS110GXS-1CF269C, LS110GXS-2CF269C, LS110GXS-1CF269I

DESCRIPTION
The AWT921 is a monolithic amplifier for use in communication systems that require high gain and output intercept point. This device has been specifically designed for multi carrier and micro cell base station applications.

FEATURES
*High output power levels
*High Efficiency
*True Surface Mount Package with Integrated Heat Slug
*Internal Bias Circuit Requiring Nominal Input Voltages+10%
*Low Cost
*Off Chip Output Matching Circuit Allows Application Optimization

GENERAL DESCRIPTION
 The patent-pending ACT8798 is a complete, costeffective, highly-efficient ActivePMUTM power management solution that is ideal for a wide range of portable handheld equipment.
This device integrates three step-down DC/DC converters and three low dropout linear regulators (LDOs) into a single, thin, space-saving package. An I2C Serial Interface provides programmability for the DC/DC converters and LDOs.
REG1, REG2 and REG3 are fixed-frequency, current-mode PWM step-down DC/DC converters that are optimized for high efficiency and are capable of supplying up to 1.2A, 1.2A and 750mA, respectively.
REG4, REG5 and REG6 are low noise, high PSRR linear regulators that are capable of supplying up to 250mA each.
The ACT8798 is available in a tiny 4mm x 4mm 24-pin Thin-QFN package that is just 0.75mm thin.

FEATURES
* Multiple Patents Pending
* Six Integrated Regulators
- 1.2A PWM Step-Down DC/DC
- 1.2A PWM Step-Down DC/DC
- 750mA PWM Step-Down DC/DC
- 250mA Low Noise LDO
- 250mA Low Noise LDO
- 250mA Low Noise LDO
* I2CTM Compatible Serial Interface
- Programmable Output Voltages
- Configurable Operating Modes
* Minimal External Components
* 4x4mm, Thin-QFN (TQFN44-24) Package
- Only 0.75mm Height
- RoHS Compliant

APPLICATIONS
* Portable Devices and PDAs
* Wireless Handhelds
* DMB Enabled Devices
* GPS Receivers, etc.

DESCRIPTION
 The UPC842GR-9LG, UPC4742GR-9LG are a high speed version of the operational amplifier UPC1251GR-9LG, UPC1251MP-KAA, UPC358GR-9LG for general single power supply use with high speed pulse response and high stabilization.
A high speed PNP transistor is used in the circuit which improves the characteristics such as a slew rate, gain-bandwidth product, stabilization of the withstand load capacitance, with no crossover distortion compared to UPC1251GR-9LG, UPC 1251MP-KAA, UPC358GR-9LG.
Therefore, UPC842GR-9LG, UPC4742GR-9LG can be used in a wide range of application circuits for single power supply AC amplifier, active filters, line driver and an amplifier for light receiving element etc.
The UPC842GR-9LG which expands temperature type is suited for wide operating ambient temperature use, and UPC4742GR-9LG is used for general purposes.
UPC844GR-9LG, UPC4744GR-9LG which are quad types with the same circuit configuration are also available as series of operational amplifiers.

FEATURES
• Slew Rate (AV = +1) 7 V/μs (TYP.)
• Stability to capacitive loads (load capacity, 1000 pF) (V+ = +5 V, V− = GND)
• Internal frequency compensation
• Gain Band Width Product 3.5 MHz (TYP.)
• Output short-circuit protection
• Input Offset Voltage ±2 mV (TYP.)
• A pin connection (pin compatible) of a standard dual operational
• Input Offset Current ±6 nA (TYP.) amplifier.
• Wide operating ambient temperature range
UPC842GR-9LG: TA = −40 to +125°C, UPC4742GR-9LG: TA = −40 to +85°C

UPC842GR-9LG-E1-A
UPC842GR-9LG-E2-A
UPC4742GR-9LG-E1-A
UPC4742GR-9LG-E2-A