Description
The IRS2609D is a high voltage, high speed power MOSFET and IGBT drivers with dependent high and low side referenced output channels. Proprietary HVIC and latch immune CMOS technologies enable ruggedized monolithic construction. The logic input is compatible with Standard CMOS or LSTTL output, down to 3.3 V logic. The output drivers feature a high pulse current buffer stage designed for minimum driver cross-conduction. The floating channel can be used to drive an N-channel power MOSFET or IGBT in the high side configuration which operates up to 600 V.

Features
*Floating channel designed for bootstrap operation
-Fully operational to +600 V
-Tolerant to negative transient voltage – dV/dt immune
*Gate drive supply range from 10 V to 20 V
*Undervoltage lockout for both channels
*3.3 V, 5 V and 15 V input logic compatible
*Cross-conduction prevention logic
*Matched propagation delay for both channels
*High side output in phase with IN input
*Internal 530 ns dead-time
*Lower di/dt gate driver for better noise immunity
*Shut down input turns off both channels
*Integrated bootstrap diode
*RoHS compliant

Applications
*Air Conditioner
*Micro/Mini Inverter Drives
*General Purpose Inverters
*Motor Control

IRS2609DSTRPbF

DESCRIPTION
The GS9029 is a second generation bipolar integrated circuit designed to drive four 75Ω co-axial cables.
The GS9029 features two pairs of complementary outputs whose amplitude is controlled within ±7.5%. The output signal levels are also adjustable from 50mVp-p up to 1000mVp-p with little change in other performance parameters. The amplitude of the output stage is varied by adjusting the RSET resistor value. The patented current mode outputs ensure superior output return loss and minimal over shoot. The rise/fall time circuitry allows wide range operation and provides symmetrical balanced outputs to reject power supply noise. In addition high output isolation ensures that the cable driver outputs are not affected by the performance or status of other outputs. Operational with input amplitudes as low as 80mV, the GS9029 provides a robust serial interface.
The GS9029 is packaged in a 16 pin narrow SOIC and operates from a single +5 or -5 volt supply. Typical system power consumption is 320mW which is 40% less than the GS9007.

FEATURES
*SMPTE 259M compliant
*four isolated outputs (two complimentary pairs), adjustable from 50mV-1000mV into 75Ω loads
*operational from 143Mb/s to 540Mb/s and beyond
*nominal 500ps rise/fall times
*precise ±7.5% output amplitudes
*40% system power reduction over GS9007
*75Ω on-chip input termination resistors
*input hysteresis
*operational down to 80mV input amplitude
*superior output isolation
*"Bus Through" expansion port for fan out requirements

APPLICATIONS
4ƒsc, 4:2:2 and 4:4:4:4 serial digital video co-axial transmission interfaces from 143 to 540Mb/s; General purpose cable driving applications (co-axial cable or UTP).

GS9029-CKD, GS9029-CTD

DESCRIPTION
The TPS65573 offers a complete solution for a charging photo flash capacitor and flashing xenon tube with insulated gate bipolar transfer (IGBT) driver. This device has an integrated voltage reference, power (SW), comparators for peak current detection/power SW turnon detection/charge complete detection, IGBT driver and control logics for charging applications/driving IGBT applications.
Compared with discrete solutions, this device reduces the component count, shrinks the total solution size, and erases the difficulty of design for xenon tube application.
Additional advantages are a fast charging time and high efficiency since this device has an optimized pulse width modulation (PWM) control algorithm for photo flash charging. Also this device has high accuracy for peak current detection and for charge completion detection. The distribution of charging time is smaller.
Other provisions of the device include sensing the output voltage at the primary side, programmable peak current at the primary side, protection features (thermal shutdown and overcurrent), an output pin for charge completion detection, input pins for charge enable, flash acceptable, and flash on.

FEATURES
*Wide Input Voltage
-VBAT = 1.4 V to 12 V
-VCC = 2.5 V to 5.5 V
*Integrated 50-V Power Switch With Lower R ON
*Programmable Peak Current at Primary Side From 0.5 A to 1.5 A
*Optimized Switch ON/OFF Control for Fast Charging
*Charge Complete Detection at Primary Side With High Accuracy
*Integrated IGBT Driver
*2-mm × 3-mm, 12-Pin WSON Package
*Protection
-Overcurrent Protection (OCP)
-Thermal Shutdown (TSD)

APPLICATIONS
*Digital Still Cameras
*Optical Film Cameras
*Digital Video Camcorders
*Cell Phones

TPS65573DSST, TPS65573DSSR

DESCRIPTION
The GS9068 is a second generation high-speed bipolar integrated circuit designed to drive one or two 75Ω co-axial cables at data rates up to 540Mb/s.
The GS9068 accepts a LVPECL level differential input, which may be AC coupled. External biasing resistors at the inputs are not required.
Power consumption is typically 160mW using a +3.3V DC power supply.

KEY FEATURES
*SMPTE 259M and SMPTE 344M compliant
*dual coaxial cable driving outputs
*50Ω differential PECL input
*single 3.3V power supply operation
*space-saving 8-lead SOIC
*operating temperature range: 0°C to 70°C
*pin compatible with GS1528 HD-LINX™ II multirate SDI dual slew-rate cable driver
*Pb-free and Green

APPLICATIONS
*SMPTE 259M Coaxial Cable Serial Digital Interfaces

GS9068-CKA, GS9068-CTA, GS9068-CKAE3, GS9068-CTAE3

General Description
The AAT3104 is a charge-pump based, current-source white LED driver capable of driving one to four LEDs up to 30mA, each. It automatically switches between 1x mode and 2x mode to maintain the highest efficiency and optimal LED current accuracy and matching.
The AAT3104 charge pump’s 1x mode (bypass mode) has very low resistance allowing LED current regulation to be maintained with input supply voltage approaching the LED forward voltage.
LED brightness is controlled using AnalogicTech’s patented S2Cwire™ single wire interface. The AAT3104 is available in a 2x2mm 10-lead SC70JW-10 package.

Features
*Drives up to 4 LEDs at up to 31mA each
*Automatic Switching Between 1x and 2x Modes
*1MHz Switching Frequency
*Linear LED Output Current Control
*Single-wire, S2Cwire Interface
-AAT3104-1: 16-step
-AAT3104-2: 32-step
*±10% LED Output Current Accuracy
*±3% LED Output Current Matching
*Low-current Shutdown Mode
*Built-in Thermal Protection
*Automatic Soft-start
*Available in 2x2mm SC70JW-10 Package

Applications
*Cordless Phone Handsets
*Digital Cameras
*Mobile Phone Handsets
*MP3 and PMP Players

AAT3104IJQ-1-T1, AAT3104IJQ-2-T1

Description
The HD66520 is a column driver for liquid crystal dot-matrix graphic display systems. This LSI incorporates 160 liquid crystal drive circuits and a 160 ´ 240 ´ 2-bit bit-map RAM, which is suitable for LCDs in portable information devices. It also includes a general-purpose SRAM interface so that draw access can be easily implemented from a general-purpose CPU. The HD66520 also has a new arbitration method which prevents flicker when the CPU performs draw access asynchronously. The on-chip display RAM greatly decreases power consumption compared to previous liquid crystal display systems because there is no need for high-speed data transfer. The chip also incorporates a four-level grayscale controller for enhanced graphics capabilities, such as icons on a screen.

Features
*Duty cycle: 1/64 to 1/240
*Liquid crystal drive circuits: 160
*Low-voltage logic circuit: 3.0 to 5.5-V operation power supply voltage
*High-voltage liquid crystal drive circuit: 8 to 28-V liquid crystal drive voltage
*Grayscale display: FRC four-level grayscale display
*Grayscale memory management: Packed pixel
*Internal bit-map display RAM: 76800 bits (160 ´ 240 lines ´ two planes)
*CPU interface
-SRAM interface
-Address bus: 16 bits, data bus: 8 bits

HD66520TA0, HD66520TB0

Description
The HFA5253 is a very high speed monolithic pin driver solution for high performance test systems. The device will switch at high data rates between two input voltage levels providing variable amplitude pulses. Slew Rate Control pins provide independent control over positive and negative slew rate allowing the customer to optimize the pin driver speed for their application. The output impedance is trimmed to achieve a precision 50Ω source for impedance matching.
Two differential ECL/TTL compatible inputs control the operation of the HFA5253, one controlling the VHIGH/VLOW switching and the other controlling the output’s highimpedance state. The HFA5253’s 800MHz data rate makes it compatible with today’s high-speed VLSI test systems and the +8V to -3V output swing satisfies the most stringent testing requirements of all common logic families.
The HFA5253 is manufactured in Harris’ proprietary complementary bipolar UHF-1 process.

Features
*High Digital Data Rate . . . . . . . . . . . . . . . . . . . . . 800MHz
*Very Fast Rise/Fall Times. . . . . . . . . . . . . . . . . . . . . 500ps
*Wide Output Range . . . . . . . . . . . . . . . . . . . . . +8V to -3V
*Precise 50Ω Output Impedance
*High Impedance, Three-State Output Control
*Slew Rate Control

Applications
*IC Tester Pin Electronics
*Pattern Generators
*Pulse Generators
*Level Comparator/Translator

HFA5253CB

GENERAL DESCRIPTION
The ADN4663 is a dual, CMOS, low voltage differential signaling (LVDS) line driver offering data rates of over 600 Mbps (300 MHz), and ultralow power consumption. It features a flow-through pinout for easy PCB layout and separation of input and output signals.
The device accepts low voltage TTL/CMOS logic signals and converts them to a differential current output of typically ±3.1 mA for driving a transmission medium such as a twisted-pair cable. The transmitted signal develops a differential voltage of typically ±355 mV across a termination resistor at the receiving end, and this is converted back to a TTL/CMOS logic level by a line receiver.
The ADN4663 and a companion receiver offer a new solution to high speed point-to-point data transmission, and a low power alternative to emitter-coupled logic (ECL) or positive emitter-coupled logic (PECL).

FEATURES
*±15 kV ESD protection on output pins
*600 Mbps (300 MHz) switching rates
*Flow-through pinout simplifies PCB layout
*300 ps typical differential skew
*700 ps maximum differential skew
*1.5 ns maximum propagation delay
*3.3 V power supply
*±355 mV differential signaling
*Low power dissipation: 23 mW typical
*Interoperable with existing 5 V LVDS receivers
*Conforms to TIA/EIA-644 LVDS standard
*Industrial operating temperature range (−40°C to +85°C)
*Available in surface-mount (SOIC) package

APPLICATIONS
*Backplane data transmission
*Cable data transmission
*Clock distribution

ADN4663BRZ, ADN4663BRZ-REEL7

General Description
The IXDD414 is a high speed high current gate driver specifically designed to drive the largest MOSFETs and IGBTs to their minimum switching time and maximum practical frequency limits. The IXDD414 can source and sink 14A of peak current while producing voltage rise and fall times of less than 30ns. The input of the driver is compatible with TTL or CMOS and is fully immune to latch up over the entire operating range. Designed with small internal delays, cross conduction/current shootthrough is virtually eliminated in the IXDD414. Its features and wide safety margin in operating voltage and power make the IXDD414 unmatched in performance and value.
The IXDD414 incorporates a unique ability to disable the output under fault conditions. When a logical low is forced into the Enable input, both final output stage MOSFETs (NMOS and PMOS) are turned off. As a result, the output of the IXDD414 enters a tristate mode and achieves a Soft Turn-Off of the MOSFET/IGBT when a short circuit is detected. This helps prevent damage that could occur to the MOSFET/IGBT if it were to be switched off abruptly due to a dv/dt over-voltage transient.
The IXDD414 is available in the standard 8-pin P-DIP (PI), 5-pin TO-220 (CI) and in the TO-263 (YI) surface-mount package.

Features
*Built using the advantages and compatibility of CMOS and IXYS HDMOSTM processes.
*Latch-Up Protected
*High Peak Output Current: 14A Peak
*Wide Operating Range: 4.5V to 25V
*Ability to Disable Output under Faults
*High Capacitive Load Drive Capability: 15nF in <30ns
*Matched Rise And Fall Times
*Low Propagation Delay Time
*Low Output Impedance
*Low Supply Current

Applications
*Driving MOSFETs and IGBTs
*Limiting di/dt under Short Circuit
*Motor Controls
*Line Drivers
*Pulse Generators
*Local Power ON/OFF Switch
*Switch Mode Power Supplies (SMPS)
*DC to DC Converters
*Pulse Transformer Driver
*Class D Switching Amplifiers

IXDD414YI, IXDD414CI

Description
IR1168 is dual smart secondary-side rectifier driver IC designed to drive two N-Channel power MOSFETs used as synchronous rectifiers in resonant converter applications. The IC can control one or more paralleled N MOSFETs to emulate the behavior of Schottky diode rectifiers. The drain to source for each rectifier MOSFET voltage is sensed differentially to determine the level of the current and the power switch is turned ON and OFF in close proximity of the zero current transition. Ruggedness and noise immunity are accomplished using an advanced blanking scheme and double-pulse suppression that allows reliable operation in fixed and variable frequency applications.

Features
*Secondary-side high speed controller for synchronous rectification in resonant half bridge topologies
*200V proprietary IC technology
*Max 500KHz switching frequency
*Anti-bounce logic and UVLO protection
*4A peak turn off drive current
*Micropower start-up & ultra low quiescent current
*10.7V gate drive clamp
*70ns turn-off propagation delay
*Wide Vcc operating range
*Direct sensing for both Synchronous Rectifiers
*Minimal component count
*Simple design
*Lead-free

Typical Applications
*LCD & PDP TV, Telecom SMPS, AC-DC adapters

IR1168SPBF, IR1168STRPBF