Description
The MC13028A is a third generation C–QUAM stereo decoder targeted for use in low voltage, low cost AM/FM E.T.R. radio applications. Advanced features include a signal quality detector that analyzes signal strength, signal to noise ratio, and stereo pilot tone before switching to the stereo mode. A “blend function” much like FM stereo has been added to improve the transition from mono to stereo. The audio output level is adjustable to allow easy interface with a variety of AM/FM tuner chips. The external components have been minimized to keep the total system cost low.

Features
*Adjustable Audio Output Level
*Stereo Blend Function
*Stereo Threshold Adjustment
*Operation from 2.2 V to 12 V Supply
*Precision Pilot Tone Detector
*Forced Mono Function
*Single Pinout VCO
*IF Amplifier with IF AGC Circuit
*VCO Shutdown Mode at Weak Signal Condition

MC13028AD, MC13028AP

Description
A range of miniature single in line (SIL) hybrid modules providing complete four channel Radio Receiver/Decoder systems available in either AM or FM. When used with the 110-AM or 120-FM series pocket keyfobs a complete remote telemetry system is obtained with up to 150 metres range.
The module consists of a front end super-heterodyne or super-regen RF receiver with an embedded microcontroller decoding a highly secure Keeloq protocol signal.
The module has an easy-to-use 'LEARN' facility, and is capable of learning up to 50 unique keyfob encoders.
The module requires a 5V power supply and provides a direct LED drive showing data reception and four digital data outputs. The outputs may be programmed for momentary or latching configuration.
The modules have flash re-programmability feature to enable field re-programming of the controller.

Features
*Miniature RF Receiver and Decoder.
*Advanced Keeloq Decoding
*Advanced Laser Trimmed Ceramic Module
*AM Range up to 100 Metres
*FM Range up to 150 Metres
*Easy Learn Transmitter Feature.
*Outputs, Momentary or Latching & Serial Data.
*Direct Led Drive Shows Data Reception
*Single Supply 5V
*Flash re-programmable
*HIR6 Low Power Version (<1mA)
*Directly compatible with 110 Series
*Compatible with RF600E
*EMC Compliant for use in Europe
*FCC Certified for use in USA

Applications
*General Remote Control Systems.
*Garage Door Openers.
*Car, Caravan, Motorcycle Alarms
*Remote Switching.
*Remote Gates.
*Paging.

HIRK-433, HIR6-433, HIRK-315A, HIRK-433A, HIR6-433A, HIRK-433F

GENERAL DESCRIPTION
This is a Call Waiting decoder used on the telephone. Call Waiting service works by alerting a customer engaged in a telephone call to a new incoming call. Thus, the customer can still receive important calls while engaged in a current call. The Call Waiting decoder can detect dual-tone (2130Hz and 2750Hz) alert tone and generate a valid timing on the data pins for micro controller.

FEATURES
*Compatible with Bellcore special report SR-TSV-002476
*3.6V ~ 6.0V supply voltage
*Call-Waiting (2130Hz plus 2750Hz) alert tone detector
*Sensitivity compensated by adjusting OP Amp
*Internal buffer
*Detection block for alert tone detected and digital algorithm detection
*Package series --- 14-pin DIP or 16-pin SOP (150 mil) AG8888AP for 14-pin DIP AG8888N for 16-pin SOP (150 mil)

APPLICATION
Feature phones, cordless phones and stand-alone product

AG8888AP, AG8888AP

Description
The RF Solutions RF600E, & RF600D are easy to use encoder and decoder I/C’s. They have been designed to achieve the maximum possible range from any radio / Infra Red transmitter receiver set.
Unlike other encoder /decoder devices the RF600E/600D provide an unprecedented level of security which prevents copying or grabbing whist also obtaining optimum range from the transmitter and receiver.
The devices are very easy to use and can be inserted directly into a circuit. The RF600D has an easy learn feature enabling it to learn up to 7 unique RF600E encoder devices in standalone mode or up to 48 encoder devices when used in conjunction with an external EEPROM.
These devices enable a simple but secure remote telemetry application whilst obtaining the maximum range from the radio set.

Features
*Highly Secure Protocol
*RF Encoder & Decoder IC’s
*Simple to Use
*Stand Alone Operation
*Achieves Maximum Range from RF Modules
*1 – 4 Switch Options (15 states)
*Decoder Serial Output
*Led Indication of Transmission
*Directly Compatible with Keeloq Decoder
*Easy Learn Feature of Transmitters
*Sleep Mode
*Up to 48 Transmitters can be Learned
*Optimum Range: AM up to 100m, FM up to 200m, IR up to 20m
*Compatible with RF Solutions Systems

Typical Applications
*General Purpose Remote Control
*Automotive alarm systems
*Gate and garage openers
*Electronic door locks
*Identity tokens
*Burglar alarm systems

RF600E, RF600E-SO, RF600DR6, RF600DR6-SO, RF600D8R6, RF600D-SO8R6

General Description
Encoders and decoders are used for physical layer coding for Gigabit Ethernet, Fibre Channel, and other applications. The 8b/10b encoder takes byte inputs, and generates a direct current (DC) balanced stream (equal number of 1s and 0s) with a maximum run length of 5. Some of the
individual 10-bit codes will have an equal number of 1s and 0s, while others will have either four 1s and six 0s, or, six 1s and four 0s. In the latter case, the disparity between 1s and 0s is used as an input to the next 10-bit code generation, so that the disparity can be reversed, and maintain an overall balanced stream. For this reason, some 8-bit inputs have two valid 10-bit codes, depending on the input disparity.

Features
*Support for Arria™ GX device family
*8b/10b encoding and decoding
*Cascaded encoding and decoding
*Industry compatible special character coding
*Easy-to-use IP MegaWizard® interface
*Support for OpenCore Plus evaluation
*IP functional simulation models for use in Altera-supported VHDL and Verilog HDL simulators

GENERAL DESCRIPTION
The XR-2211 is a monolithic phase-locked loop (PLL) system especially designed for data communications applications.
It is particularly suited for FSK modem applications.
It operates over a wide supply voltage range of 4.5 to 20V and a wide frequency range of 0.01Hz to 300kHz.
It can accommodate analog signals between 10mV and 3V, and can interface with conventional DTL, TTL, and ECL logic families.
The circuit consists of a basic PLL for tracking an input signal within the pass band, a
quadrature phase detector which provides carrier detection, and an FSK voltage comparator which provides FSK demodulation.
External components are used to independently set center frequency, bandwidth, and output
delay.
An internal voltage reference proportional to the power supply is provided at an output pin.
The XR-2211 is available in 14 pin packages specified for military and industrial temperature ranges.

FEATURES
*Wide Frequency Range, 0.01Hz to 300kHz
*Wide Supply Voltage Range, 4.5V to 20V
*HCMOS/TTL/Logic Compatibility
*FSK Demodulation, with Carrier Detection
*Wide Dynamic Range, 10mV to 3V rms
*Adjustable Tracking Range, +1% to 80%
*Excellent Temp. Stability, +50ppm/°C, max.

APPLICATIONS
*Caller Identification Delivery
*FSK Demodulation
*Data Synchronization
*Tone Decoding
*FM Detection
*Carrier Detection

XR-2211M
XR-2211N
XR-2211P
XR-2211ID

FUNCTIONAL DESCRIPTION
 The 3D7522 product family consists of monolithic CMOS Manchester Decoders.
The unit accepts at the RX input a bi-phase-level, embedded-clock signal.
In this encoding mode, a logic one is represented by a high-to-low transition within the bit cell, while a logic zero is represented by a low-to-high transition.
The recovered clock and data signals are presented on CLK and DATB, respectively, with the data signal inverted.
The operating baud rate (in MBaud) is specified by the dash number.
The input baud rate may vary by as much as ±15% from the nominal device baud rate without compromising the integrity of the information received.
Because the 3D7522 is not PLL-based, it does not require a long preamble in order to lock onto the received signal.
Rather, the device requires at most one bit cell before the data presented at the output is valid.
This is extremely useful in cases where the information arrives in bursts and the input is otherwise turned off.
The all-CMOS 3D7522 integrated circuit has been designed as a reliable, economic alternative to hybrid TTL Manchester Decoders.
It is TTL- and CMOS-compatible, capable of driving ten 74LS-type loads.
It is offered in space saving surface mount 8-pin and 14-pin SOICs.

FEATURES
• All-silicon, low-power CMOS technology
• TTL/CMOS compatible inputs and outputs
• Vapor phase, IR and wave solderable
• Low ground bounce noise
• Maximum data rate: 50 MBaud
• Data rate range: ±15%
• Lock-in time: 1 bit

3D7522-0.5
3D7522-1
3D7522-5
3D7522-10
3D7522-20
3D7522-25
3D7522-50

Silicon Image’s M2VD-2HL* is designed to be used in system-on-a-chip solutions for
DVD and STB/DTV markets. With its extensive set of features M2VD-2HL enables companies
to easily provide functions like parallel viewing and recording, picture-in-picture or
simultaneous viewing of several channels in television, PC or other relevant environments.
The M2VD-2HL decoder is optimized to satisfy a wide range of applications and
technologies with optimal performance at lowest possible silicon costs. Its interfaces are
optimized for easy integration into a System-on-Chip architecture using the standard onchip
bus approach. This dramatically reduces the integration effort and enables fast
time-to-market developments.

Features
• ISO/IEC 13818-2 - MPEG-2 Main Profile @ High Level
• ISO/IEC 11172-2 - MPEG-1 constrained parameter set
• Support of all ATSC and DVB HDTV formats
• Real-time decoding of multiple streams only limited by frequency.
• Error detection and autonomous error concealment with concealment vectors on slice,
macroblock and block layer
• Counter for concealed MBs within a picture and threshold register which indicates the level
of interrupt generation
• Software access to relevant internal registers and parameter stores to provide the possibility
of a flexible error handling and a robust and error tolerant decoding control
• Decoding of Packetized Elementary Stream (PES) and Elementary Stream (ES)

Applications
• Set-top boxes
• Digital TV sets and IPTV applications
• DVD players and recorders
• Portable multimedia players
• Surveillance

FEATURES
* Single Chip DVD Decoder Solution
* Multiple Standard Support: CVD, SuperVCD, VideoCD, DVCD
* DVD-Audio Support
* Integrated 54 MIPS Audio DSP
* Embedded NTSC/PAL Encoder w/ 10-bit Video DACs
* DTS™, Dolby Digital™, Pro Logic™, and MPEG 5.1 Audio Decoding
* Virtual Surround Sound, 3D Headphones, Music Modes
* Enhanced Karaoke
* Simultaneous 2 Channel, 6 Channel, and S/PDIF Audio Outputs
*  Image Enhancement Filtering: Progressive Interpolation, Sharpening, and Brightness Equalization
*  Advanced Trick Play Features including Zoom, Smooth Scan
*  Enhanced On-Screen-Display with 32 Colors and 8 Blending Levels
*  Functionally Compatible with Vaddis Family Decoders
*  176-pin TQFP Package
*  1.1 W Power Consumption in full operation
*  0.25 Micron Technology

DESCRIPTION
The ZR36730 Vaddis IV DVD decoder is targeted at fourth generation DVD and convergence products. With its high level of integration and flexibility, the ZR36730 is a versatile digital video
and audio processor. This new generation part builds upon Zoran’s success in the DVD market, incorporating enhanced audio and video functionality. Leading audio algorithms, such as HDCD, MP3, DTS, Dolby Digital, Pro Logic, and MPEG 5.1 decoding are supported in this single chip solution. In addition, the video feature set has been expanded to include image
quality enhancements and augmented On-Screen-Display (OSD) functionality. Through the StandardPlusTM design methodology, Zoran is building upon the standard to provide leading-edge capabilities for advanced DVD players and convergence devices, such as WebDVD players.

DVD Decoding
The ZR36730 handles all aspects of DVD decoding according to the specification. This single chip solution performs DVD authentication/decryption, demux and parsing, MPEG-2 or MPEG-1 video decode, sub-picture decode, highlight processing, and audio/video synchronization. The integrated OSD unit provides 32 colors and 8 blending levels which are necessary for sophisticated on-screen user interfaces. In addition, DVD-Audio is supported by the ZR36730’s integrated digital audio processor.

Highest Quality Audio
With its integrated 54 MIPS Audio Decode Processor (ADP unit), the ZR36730 is capable of supporting a host of advanced audio algorithms. Based on Zoran’s field proven audio DSP
technology, the ADP unit enables the development of a DVD system which meets the highest quality audio output standards, such as for Dolby certification. In addition, algorithms from our
SiliconSoftwareTM library are supported, including 3D Headphones and enhanced Karaoke. The embedded ADP unit is a 20-bit audio DSP enabling Vaddis solutions to deliver audiophile quality output.

General Description
The CD4511BC BCD-to-seven segment latch/decoder/driver is constructed with complementary MOS (CMOS) enhancement mode devices and NPN bipolar output drivers in a single monolithic structure. The circuit provides the functions of a 4-bit storage latch, an 8421 BCD-to-seven segment decoder, and an output drive capability. Lamp test (LT), blanking (BI), and latch enable (LE) inputs are used to test the display, to turn-off or pulse modulate the brightness of the display, and to store a BCD code, respectively. It can be used with seven-segment light emitting diodes (LED), incandescent, fluorescent, gas discharge, or liquid crystal readouts either directly or indirectly.
 Applications include instrument (e.g., counter, DVM, etc.) display driver, computer/calculator display driver, cockpit display driver, and various clock, watch, and timer uses.

Features
* Low logic circuit power dissipation
* High current sourcing outputs (up to 25 mA)
* Latch storage of code
* Blanking input
* Lamp test provision
* Readout blanking on all illegal input combinations
* Lamp intensity modulation capability
* Time share (multiplexing) facility
* Equivalent to Motorola MC14511

CD4511BCWM CD4511BCN