Description
The MPL115A1 is an absolute pressure sensor with digital output for low cost applications. A miniature 5 x 3 x 1.2 mm LGA package ideally suits it for portable electronics and space constrained applications. Low current consumptions of 5 μA during Active mode and 1 μA during Shutdown (Sleep) mode target battery and other low-power applications. A wide operating temperature range from -40°C to +105°C fits demanding environmental requirements.
MPL115A1 employs a MEMS pressure sensor with a conditioning IC to provide accurate pressure measurement from 50 to 115 kPa. An integrated ADC provides digitized temperature and pressure sensor outputs via a SPI port. Calibration Data is stored in internal ROM. Utilizing raw sensor output, the host microcontroller executes a compensation algorithm to render Compensated Absolute Pressure with 1 kPa accuracy.
The MPL115A1 pressure sensor’s small form factor, low power capability, precision, and digital output optimize it for barometric measurement applications.

Features
*Digitized pressure and temperature information together with programmed calibration coefficients for host micro use.
*Factory Calibrated
*50 kPa to 115 kPa Absolute Pressure
*1 kPa Accuracy
*2.375 V to 5.5 V Supply
*Integrated ADC
*SPI Interface
*Monotonic Pressure and Temperature Data Outputs
*Surface Mount RoHS Compliant Package

Application Examples
*Barometry (portable and desk-top)
*Altimeters
*Weather Stations
*Hard Disk-Drives (HDD)
*Industrial Equipment
*Health Monitoring
*Air Control Systems

MPL115A1T1

Description
The MMA62XXAEG series of dual axis (X and Y) silicon capacitive, micromachined accelerometers features a full digital signal processing for filtering, trim and data formatting. It has been optimized for analog output and offers an over-damped transducer.

Features
*Available in ±20/20g, ±50/50g, or ±100/100g versions. Additional g-ranges between 20 and 100g may be available upon request
*Full-scale range is independently specified for each axis
*400 Hz, 4 Pole, 16 μs sample time, additional filter options are available
*Ratiometric analog voltage output
*Capture/hold input for system-wide synchronization support
*3.3 or 5 V single supply operation
*On-chip temperature sensor and voltage regulator
*Internal self-test
*Minimal external component requirements
*Pb-free 20-pin SOIC package
*Automotive AEC -Q100 qualified

Typical Applications
*Crash detection (Airbag)
*Impact and vibration monitoring
*Shock detection

MMA6255AEG, MMA621010AEG, MMA6222AEGR2, MMA6255AEGR2

Description
The MPX2102 series devices are silicon piezoresistive pressure sensors providing a highly accurate and linear voltage output directly proportional to the applied pressure. The sensor is a single, monolithic silicon diaphragm with the strain gauge and a thin-film resistor network integrated on-chip. The chip is laser trimmed for precise span and offset calibration and temperature compensation.

Features
*Temperature Compensated Over 0°C to +85°C
*Easy-to-Use Chip Carrier Package Options
*Available in Absolute, Differential and Gauge Configurations
*Absolute, Differential and Gauge Options

Application Examples
*Pump/Motor Control
*Robotics
*Level Detectors
*Medical Diagnostics
*Pressure Switching
*Barometers
*Altimeters

MPX2102A, MPX2102DP, MPX2102AP, MPX2102GP, MPX2102ASX, MPX2102GVP

Description
Freescale Semiconductor has developed a low cost, high volume, miniature pressure sensor package which is ideal as a sub-module component or a disposable unit. The unique concept of the Chip Pak allows great flexibility in system design while allowing an economic solution for the designer. This new chip carrier package uses Freescale Semiconductor's unique sensor die with its piezoresistive technology, along with the added feature of on-chip, thin-film temperature compensation and calibration.

Features
*Low Cost
*Integrated Temperature Compensation and Calibration
*Ratiometric to Supply Voltage
*Polysulfone Case Material (Medical, Class V Approved)
*Provided in Easy-to-Use Tape and Reel

Application Examples
*Medical Diagnostics
*Infusion Pumps
*Blood Pressure Monitors
*Pressure Catheter Applications
*Patient Monitoring

MPX2301DT1

Description
Freescale Semiconductor has developed a low cost, high volume, miniature pressure sensor package which is ideal as a sub-module component or a disposable unit. The unique concept of the Chip Pak allows great flexibility in system design while allowing an economic solution for the designer. This new chip carrier package uses Freescale Semiconductor's unique sensor die with its iezoresistive technology, along with the added feature of on-chip, thin-film emperature compensation and calibration.

Features
*Low Cost
*Integrated Temperature Compensation and Calibration
*Ratiometric to Supply Voltage
*Polysulfone Case Material (Medical, Class V Approved)
*Provided in Easy-to-Use Tape and Reel

Application Examples
*Respiratory Diagnostics
*Air Movement Control
*Controllers
*Pressure Switching

MPXC2011DTI, MPXC2012DTI

OVERVIEW
The MPR083 is an Inter-Integrated Circuit Communication (I2C) driven Capacitive Touch Sensor Controller, optimized to manage an 8-position rotary shaped capacitive array. The device can accommodate a wide range of implementations through 3 output mechanisms, and many configurable options.

Features
*1.8 V to 3.6 V operation
*41 μA average supply current with 1 s response time
*2 μA Standby Current
*Variable low power mode response time (32 ms – 4 s)
*Rejects unwanted multi-key detections from EMI events such as PA bursts or user handling
*Ongoing pad analysis and detection is not reset by EMI events
*Data is buffered in a FIFO for shortest access time
*IRQ output advises when FIFO has data
*System can set interrupt behavior as immediate after event, or program a minimum time between successive interrupts
*Current rotary position is always available on demand for pollingbased systems
*Sounder output can be enabled to generate key-click sound when rotary is touched
*Two hardware selectable I2C addresses allowing two devices on a single I2C bus
*Configurable real-time auto calibration
*5 mm x 5 mm x 1 mm 16 lead QFN package
*-40°C to +85°C operating temperature range
 
Implementations
*Control Panels
*Switch Replacements
*Rotary and Linear Sliders

Typical Applications
*Appliances
*PC Peripherals
*Access Controls
*MP3 Players
*Remote Controls
*Mobile Phones

MPR083Q, MPR083EJ

Description
The 34716 is a highly integrated, space-efficient, low cost, dual synchronous buck switching regulator with integrated N-channel power MOSFETs. It is a high performance point-of-load (PoL) power supply with its second output having the ability to track an external reference voltage. it provides a full power supply solution for Double-Data-Rate (DDR) Memories.
Channel one provides a source only, 5.0 A drive capability, while channel two can sink and source up to 3.0 A. Both channels are highly efficient with tight output regulation. With its high current drive capability, channel one can be used to supply the VDDQ to the memory chipset. The second channel’s ability to track a reference voltage makes it ideal to provide the termination voltage (VTT) for modern data buses. The 34716 also provides a buffered output reference voltage (VREFOUT) to the memory chipset The 34716 offers the designer the flexibility of many control, supervisory, and protection functions to allow for easy implementation of complex designs. It is housed in a Pb-free, thermally enhanced, and space efficient 26-Pin Exposed Pad QFN.

Features
*50 mΩ integrated N-channel power MOSFETs
*Input voltage operating range from 3.0 to 6.0 V
*±1% accurate output voltages, ranging from 0.7 to 3.6 V
*The second output tracks 1/2 an external reference voltage
*±1% accurate buffered reference output voltage
*Programmable switching frequency range from 200 kHz to 1.0 MHz
*Programmable soft start timing for channel one
*Over-current limit and short-circuit protection on both channels
*Thermal shutdown
*Output over-voltage and under-voltage detection
*Active low power good output signal
*Active low standby and shutdown inputs
*Pb-free packaging designated by suffix code EP.

MC34716EP/R2

Description
Designed for N-CDMA base station applications with frequencies from 1930 to 1990 MHz. Suitable for TDMA, CDMA and multicarrier amplifier applications.
To be used i n Class AB for PCN - PCS/cel lular radi o and WLL applications.
*Typical 2-Carrier N-CDMA Performance: VDD = 28 Volts, IDQ = 950 mA
Pout = 22 Watts Avg., Full Frequency Band, IS-95 CDMA (Pilot, Sync, Paging, Traffic Codes 8 Through 13) Channel Bandwidth = 1.2288 MHz.
PAR = 9.8 dB @ 0.01% Probability on CCDF.
- Power Gain - 14.5 dB
- Drain Efficiency - 25.5%
- IM3 @ 2.5 MHz Offset - -37 dBc in 1.2288 MHz Bandwidth
- ACPR @ 885 kHz Offset - -51 dBc in 30 kHz Bandwidth
*Capable of Handling 5:1 VSWR, @ 28 Vdc, 1960 MHz, 100 Watts CW Output Power

Features
*Characterized with Series Equivalent Large-Signal Impedance Parameters
*Internally Matched for Ease of Use
*Qualified Up to a Maximum of 32 VDD Operation
*Integrated ESD Protection
*N Suffix Indicates Lead-Free Terminations
*Designed for Lower Memory Effects and Wide Instantaneous Bandwidth Applications
*200°C Capable Plastic Package
*RoHS Compliant
*In Tape and Reel. R1 Suffix = 500 Units per 44 mm, 13 inch Reel.

MRF6S19100NBR1, MRF6S19100N

Description
*24 Vdc Supply, 47 to 870 MHz, CATV GaAs Forward Amplifier Module
*Replaced MHW9206. There are no form, fit or function changes with this part replacement.
*RoHS Compliant

Features
*Specified for 79 - , 112- and 132-Channel Loading
*Excellent Distortion Performance
*Built -in Input Diode Protection
*GaAs FET Transistor Technology
*Unconditionally Stable Under All Load Conditions

Applications
*CATV Systems Operating in the 47 to 870 MHz Frequency Range
*Input Stage Amplifier in Optical Nodes, Line Extenders and Trunk Distribution Amplifiers for CATV Systems
*Output Stage Amplifier on Applications Requiring Low Power Dissipation and High Output Performance
*Driver Amplifier in Linear General Purpose Applications

The MPVZ4006G series piezoresistive transducers are state-of-the-art monolithic silicon pressure sensors designed for the appliance, consumer, health care and industrial market.
The analog output can be read directly into the A/D input of Freescale microcontrollers.
This transducer combines advanced micromachining techniques, thin-film metallization, and bipolar processing to provide an accurate, high level analog output signal that is proportional to the applied pressure.
The axial port has been modified to accommodate industrial grade tubing.

Features
* 2.5% Maximum Error over +10°C to +60°C with Auto Zero
* 5% Maximum Error over +10°C to +60°C without Auto Zero
* Durable Thermoplastic (PPS) Package
* Available in Surface Mount (SMT) or Through-Hole (DIP) Configurations

Application Examples
* Washing Machine Water Level Measurement (Reference AN1950)
* Ideally Suited for Microprocessor or Microcontroller-Based Systems
* Appliance Liquid Level and Pressure Measurement
* Respiratory Equipment

MPVZ4006GW6U
MPVZ4006GW7U
MPVZ4006G6U
MPVZ4006G6T1
MPVZ4006G7U