Description
The SG1577A is a high-efficiency, voltage-mode, dualchannel, synchronous DC/DC PWM controller for two independent outputs. The two channels are operated out of phase. The internal reference voltage is trimmed to 0.7V±1.5%. It is connected to the error amplifier’s positive terminal for voltage feedback regulation.
The soft-start circuit ensures the output voltage can be gradually and smoothly increased from zero to its final regulated value. The soft-start pin can also be used for chip-enable function. When two soft-start pins are grounded, the chip is disabled and the total operation current can be reduced to under 0.7mA.
The fixed-frequency is programmable from 60kHz to 340kHz. The Over-Current Protection (OCP) level can be programmed by an external current sense resistor. It has two integrated sets of internal MOSFET drivers.
SG1577A is available in a 20-pin SOP package.

Features
*Integrated Two Sets of MOSFET Drivers
*Two Independent PWM Controllers
*Constant Frequency Operation: Free-running Fixed Frequency Oscillator Programmable: 61kHz to 340kHz
*Maximum Input Supply Voltage: 15V
*Programmable Output as Low as 0.7V
*Internal Error Amplifier Reference Voltage: 0.7V±1.5%
*Two Soft-Start / EN Functions
*Programmable Over-Current Protection (OCP)
*30V HIGH Voltage Pin for Bootstrap Voltage
*Output Over-Voltage Protection (OVP)
*20-Pin SOP

Applications
*CPU and GPU Vcore Power Supply
*Power Supply Requiring Two Independent Outputs

SG1577ASY

Description
The FAN2564 operates from a minimum input of 1.65V and provides outputs as low as 1.2V. Output current is guaranteed to 300mA, making this regulator ideal for digital loads.
The unique low input voltage capability and very low dropout make this device an ideal post regulator to a synchronous buck regulator. In this configuration, accurate low voltage regulation is provided without the inefficiencies typically related to linear regulators.
The enable pin can be used to initiate shutdown mode, where the operating current falls to an extremely low 10nA, typically.
The FAN2564 is designed to be stable with spacesaving ceramic capacitors as small as 0402 case size.
The FAN2564 is available in 4-bump 0.5mm pitch wafer-level chip-scale package (WLCSP) and a 6-lead 2 x 2mm ultra-thin molded leadless package (UMLP).

Features
*Input Voltage 1.65V to 3.6V
*Guaranteed 300mA Output
*High Initial Output Voltage Accuracy: ±1%
*Fixed Output Voltage options from 1.2V to 2.8V
*Very Low Dropout: 100mV at 300mA
*45μA Quiescent Current at No Load
*Low Output Noise of 100μVRMS
*Inrush Current Controlled to Less Than 500mA
*PSRR of 60dB at 1kHz
*100μs Startup Time
*Stable with Ceramic Capacitors
*Thermal and Short-Circuit Protection
*4-bump WLCSP, 0.5mm Pitch
*6-pin 2 x 2mm UMLP

Applications
*Post Regulator
*Cell Phones and Smart Phones
*WLAN, 3G, and 4G Data Cards
*PMP and MP3 Players

FAN2564UC12X, FAN2564UC13X, FAN2564UMP12X, FAN2564UMP13X

Description
The FSDM0465RS is an integrated Pulse-Width Modulator (PWM) and SenseFET specifically designed for high-performance offline Switch Mode Power Supplies (SMPS) with minimal external components. The device is an integrated, high-voltage, powerswitching regulator that combines an avalanche rugged SenseFET with a current mode PWM control block. The PWM controller includes integrated fixed-frequency oscillator, under-voltage lockout, leading-edge blanking (LEB), optimized gate driver, internal soft-start, temperature-compensated precise-current sources for a loop compensation and self-protection circuitry. Compared with a discrete MOSFET and PWM controller solution, it reduces total cost, component count, size and weight; while increasing efficiency, productivity and system reliability. This device is a basic platform well suited for cost effective designs of flyback converters.

Features
*Internal Avalanche Rugged SenseFET
*Advanced Burst-Mode Operation Consumes under 1W at 240VAC and 0.5W Load
*Precision Fixed Operating Frequency: 66kHz
*Internal Startup Circuit
*Improved Pulse-by-Pulse Current Limiting
*Over-Voltage Protection (OVP)
*Overload Protection (OLP)
*Internal Thermal Shutdown Function (TSD)
*Abnormal Over-Current Protection (AOCP)
*Auto-Restart Mode
*Under-Voltage Lock Out (UVLO) with Hysteresis
*Low Operating Current: 2.5mA
*Built-in Soft-Start

Applications
*SMPS for LCD Monitor and STB
*Adaptor

FSDM0465RSWDTU

Description
The FAN2560 is a linear low-dropout (LDO) regulator with a split-supply architecture. Separate bias and supply inputs allow bias to be taken directly from the battery, while the input is taken from a lower preregulated source. This allows a smaller differential voltage between input and output, which provides greater efficiency over a wider VBAT range.
The FAN2560 is available in a fixed-voltage output, 5-bump, WLCSP package.

Features
*55μA Typical Quiescent Current
*Up to 350mA Output Current
*2.9V to 5.5V Bias Supply Voltage
*VOUT+0.1V to 5.5V Power Input Supply Voltage
*Fixed Voltage Options: 1.3V and 1.5V
*Thermal Shutdown Protection (TSD)
*Input Under-Voltage Lockout (UVLO)
*Short-Circuit Current Protection (SCP)
*5-bump 0.96 x 1.33mm WLCSP

Applications
*Moderate Current Digital Loads
*DVB-H, DMB Processors
*Handsets, Smartphones
*WLAN DC-DC Converter Modules
*PDA, DSC, PMP, and MP3 Players
*Portable Hard Disk Drives

FAN2560UC13X, FAN2560UC15X

Description
The highly integrated SG6742HL/HR PWM controller provides several features to enhance the performance of flyback converters.
To minimize standby power consumption, a proprietary green-mode function provides off-time modulation to linearly decrease the switching frequency at light-load conditions. To avoid acoustic-noise problems, the minimum PWM frequency is set above 22KHz. This green-mode function enables the power supply to meet international power conservation requirements. With the internal high-voltage startup circuitry, the power loss due to bleeding resistors is eliminated. To further reduce power consumption, SG6742HL/HR is manufactured using the BiCMOS process, which allows an operating current of 2.7mA.
SG6742HL/HR integrates a frequency-hopping function internally that helps reduce EMI emission of a power supply with minimum line filters. Its built-in synchronized slope compensation achieves stable peak-current-mode control. The proprietary, internal line compensation ensures constant output power limit over a wide AC input voltage range, from 90VAC to 264VAC.
SG6742HL/HR provides many protection functions. In addition to cycle-by-cycle current limiting, the internal open-loop protection circuit ensures safety should an open-loop or output short-circuit failure occur. PWM output is disabled until VDD drops below the UVLO lower limit, when the controller starts up again. As long as VDD exceeds ~25V, the internal OVP circuit is triggered.
SG6742HL/HR is available in an 8-pin SOP package.

Features
*High-Voltage Startup
*Low Operating Current: 2.7mA
*Linearly Decreasing PWM Frequency to 22KHz
*Frequency Hopping to Reduce EMI Emission
*Fixed PWM Frequency: 100KHz
*Peak-Current-Mode Control
*Cycle-by-Cycle Current Limiting
*Leading-Edge Blanking (LEB)
*Synchronized Slope Compensation
*Internal Open-Loop Protection
*GATE Output Maximum Voltage Clamp: 18V
*VDD Under-Voltage Lockout (UVLO)
*VDD Over-Voltage Protection (OVP)
*Programmable Over-Temperature Protection (OTP)
*Internal Latch Circuit (OVP, OTP)
*Internal-Sense, Short-Circuit Protection
*Built-in 6ms Soft-Start Function
*Constant Power Limit (Full AC Input Range)
*Internal OTP Sensor with Hysteresis

Applications
General-purpose switch-mode power supplies and flyback power converters, including:
*Power Adapters
*Open-Frame SMPS

SG6742HLSY, SG6742HRSY

Description
The FSQ0170RNA, FSQ0270RNA, FSQ0370RNA consists of an integrated current mode Pulse Width Modulator (PWM) and an avalanche-rugged 700V Sense FET. It is specifically designed for high-performance offline Switch Mode Power Supplies (SMPS) with minimal external components. The integrated PWM controller features include: a fixed-frequency generating oscillator, Under-Voltage Lockout (UVLO) protection, Leading Edge Blanking (LEB), an optimized gate turn-on/ turn-off driver, Thermal Shutdown (TSD) protection, and temperature compensated precision current sources for loop compensation and fault protection circuitry.
Compared to a discrete MOSFET and controller or RCC switching converter solution, the FSQ0170RNA, FSQ0270RNA, FSQ0370RNA reduces total component count, design size, and weight while increasing efficiency, productivity, and system reliability. These devices provide a basic platform that is well suited for the design of cost-effective flyback converters, as in PC
auxiliary power supplies.

Features
*Internal Avalanche Rugged 700V SenseFET
*Consumes only 0.8W at 230 VAC & 0.5W Load with Burst-Mode Operation
*Precision Fixed Operating Frequency, 100kHz
*Internal Start-up Circuit and Built-in Soft-Start
*Pulse-by-Pulse Current Limiting and Auto-Restart  Mode
*Over-Voltage Protection (OVP), Overload Protection (OLP), Internal Thermal Shutdown Function (TSD)
*Under-Voltage Lockout (UVLO)
*Low Operating Current (3mA)
*Adjustable Peak Current Limit

Applications
*Auxiliary Power Supply for PC and Server
*SMPS for VCR, SVR, STB, DVD & DVCD Player, Printer, Facsimile & Scanner
*Adapter for Camcorder

FSQ0270RNA, FSQ0370RNA

Description
The FIN212AC μSerDes™ is a low-power serializer / deserializer optimized for use in cell phone displays and camera paths. The device reduces a 12-bit data path to four wires. The device can be configured as a serializer or deserializer through the DIRI pin, minimizing
component types in the system. For camera applications, an additional master clock can be passed in the opposite direction of data flow.
The device utilizes Fairchild’s proprietary ultra-low power, low-EMI technology. LV-CMOS parallel output buffers have been implemented with slew rate control to adjust for capacitive loading and to minimize EMI. The device also supports an ultra-low power-down mode for
conserving power in battery-operated applications.
The device is available in a 5x5mm MLP package to attach directly to a flex circuit, or in two choices of BGA, where space constraints are a concern.

Features
*Low Power Consumption
*Low Power, Proprietary, CTL™ I/O Serial Interface
*Wide PLL Input Frequency Range
*Wide Parallel Supply Voltage Range: 1.65 to 3.6V
*Low Power Core Operation: VDDS/A=2.5 to 3.6V
*Built-in LV-CMOS Voltage Translation Capability with no External Components
*Adjustable Parallel Edge Rate
*Operates as Serializer or Deserializer
*Standby Power-Down Mode Support
*Built-in Differential Termination

Applications
*8-Bit LCD Displays for Cell Phones
*8/10-Bit Cell Phone Camera Interface
*8-Bit LCD Displays for Printers

FIN212ACMLX, FIN212ACGFX, FIN212ACBFX

Description
The H11AG1M device consists of a Gallium-Aluminum- Arsenide IRED emitting diode coupled with a silicon phototransistor in a dual in-line package. This device provides the unique feature of the high current transfer ratio at both low output voltage and low input current. This makes it ideal for use in low power logic circuits, telecommunications equipment and portable electronics isolation applications.

Features
*High efficiency low degradation liquid epitaxial IRED
*Logic level compatible, input and output currents, with CMOS and LS/TTL
*High DC current transfer ratio at low input currents (as low as 200μA)
*Underwriters Laboratory (UL) recognized File #E90700, Volume 2
*IEC 60747-5-2 approved (ordering option V)
 
Applications
*CMOS driven solid state reliability
*Telephone ring detector
*Digital logic isolation


H11AG1M, H11AG1SM, H11AG1SR2M, H11AG1TM, H11AG1VM, H11AG1TVM, H11AG1SVM, H11AG1SR2VM

GENERAL DESCRIPTION
The CCD191 is a 6000 element line image sensor designed for scanning applications which require very high resolution, high sensitivity and very wide dynamic range.
Incorporation of on-chip anti-blooming and integration controls allow the CCD191 to be extremely useful in industrial measurement and control environments, or in environments where lighting conditions are difficult to control.
The CCD191 is a third generation device having an overall improved performance compared with first and second generation devices, including enhanced blue response and excellent low light level performance. The photoelement size is 10μm (0.39 mils) x 10μm (0.39 mils) on 10μm (0.39 mils) centers. The device is manufactured using Fairchild Imaging’s advanced chargecoupled device n-channel isoplanar buried-channel technology.

FEATURES
*6000 x 1 photosite array
*10 μm x 10μm photosites on 10μm pitch
*Anti-blooming and integration control
*Enhanced spectral response (particularly in the blue region)
*Excellent low-light-level performance
*Low dark signal
*Very high responsivity
*High speed operation
*Dynamic range typical: 15000:1
*Over 3 V peak-to-peak outputs
*Special selection available - consult factory
*AR coated window

General Description
This device contains six independent gates each of which performs a buffer function.
The open-collector outputs require external pull-up resistors for proper logical operation.

DM7407M
DM7407N