Description
The Agilent E1418A 8/16-Channel D/A Converter is a C–size, 1-slot, register-based VXI module. It
consists of 8 or 16 fully independent, isolated or non-isolated, 16-bit D/As. Each channel can be set to voltage or current mode with local or remote sensing on voltage outputs. All outputs can be updated with registerlevel programming to allow fast backplane access. Each channel can be updated individually, or by using the internal data buffer, synchronized so that all channels change simultaneously. The channel output mode is set with jumpers in the terminal block for each channel or by register programming. Each D/A converter can be calibrated without removal through software commands and use of the terminal block CALBUS in conjunction with a 5.5-digit multimeter. The on/off terminal block has standard screw terminals for fi eld wiring.
Refer to the Agilent Technologies Website for instrument driver availability and downloading instructions, as well as for recent product updates, if applicable.

Features
*1-Slot, C-size, register based
*8/16 independent channels, fl exible and confi gurable
*Individual isolation per channel
*16-bit resolution D/A per channel
*Programmable selectable voltage/current modes
*Software controlled calibration

E1418A001, E1418A002, E1418A003, E1418AA3E, E1418AA3H

Description
The HSDL-3202 is a new generation of low-cost Infrared (IR) transceiver modules from Agilent Technologies. It features one of the smallest footprints in the industry at 2.5 H x 8.0 W x 3.0 D mm. Although the supply voltage can range from 2.7 V to 3.6 V, the LED drive current is internally compensated to a constant 32 mA to guarantee link distance of IrDA Data 1.3 (low power) physical layer specification.
The HSDL-3202 meets the link distance of 20 cm to other IrDA 1.3 low power devices, and 30 cm to standard one meter IrDA 1.3 devices. It is designed to interface to input/output logic circuits as low as 1.8 V.

Features
*Ultra small surface mount package
*Minimal height: 2.5 mm
*VCC from 2.7 to 3.6 volts
*Interface to input/output logic circuits as low as 1.8 V
*LED supply voltage can range from 2.7 to 6 volts
*Low ICC shutdown current
-10 nA typical
*Complete shutdown
-TxD, RxD, PIN diode
*Three optional external components
*Temperature performance guaranteed, -25°C to 85°C
*32 mA LED drive current
*Integrated EMI shield
*IEC825-1 class 1 eye safe
*Edge detection input
-prevents the LED from long turn on time

Applications
*Mobile telecom
-cellular phones
-pagers
-smart phones
*Data communication
-PDAs
-portable printers
*Digital imaging
-digital cameras
-photo-imaging printers
*Electronic wallet

Description
The ADNS-3080 is a high performance addition to Agilent’s popular ADNS family of optical mouse sensors.
The ADNS-3080 is based on a new, faster architecture with improved navigation. The sensor is capable of sensing high speed mouse motion - up to 40 inches per second and acceleration up to 15g – for increased user precision and smoothness.
The ADNS-3080 along with the ADNS-2120 (or ADNS-2120-001) lens, ADNS-2220 (or ADNS-2220-001) assembly clip and HLMP-ED80-XX000 form a complete, compact optical mouse tracking system. There are no moving parts, which means high reliability and less maintenance for the end user. In addition, precision optical alignment is not required, facilitating high volume assembly.
The sensor is programmed via registers through a four-wire serial port. It is packaged in a 20-pin staggered dual inline package (DIP).

Features
*High speed motion detection – up to 40 ips and 15g
*New architecture for greatly improved optical navigation technology
*Programmable frame rate over 6400 frames per second
*SmartSpeed self-adjusting frame rate for optimum performance
*Serial port burst mode for fast data transfer
*400 or 1600 cpi selectable resolution
*Single 3.3 volt power supply
*Four-wire serial port along with Chip Select, Power Down, and Reset pins

Applications
*Mice for game consoles and computer games
*Mice for desktop PC’s, Workstations, and portable PC’s
*Trackballs
*Integrated input devices

ADNS-3080, ADNB-3081, ADNB-3082, ADNS-2120

Description
The HSDL-3000 is a small form factor infrared (IR) transceiver module that provides interface between logic and IR signals for through-air, serial, half-duplex IR data link. The module is compliant to IrDA Physical Layer Specifications 1.3 and is IEC 825-Class 1 eye safe.
The HSDL-3000 can be shut down completely to achieve very low power consumption. In the shutdown mode, the PIN diode will be inactive and thus producing very little photocurrent even under very bright ambient light. Such features are ideal for battery-operated handheld products.
The HSDL-3000 has two front packaging type options (HSDL-3000#007/017). Both options have
an integrated shield that helps to ensure low EMI emission and high immunity to EMI field, thus enhancing reliable performance.

Features
*Fully compliant to IrDA 1.3 specifications:
-2.4 kbps to 115.2 kbps
-Excellent nose-to-nose operation
-Typical link distance > 1.5 m
*Guaranteed temperature performance, –20 to 70 °C
-Critical parameters are guaranteed over temperature and supply voltages
*Low power consumption
-Low shutdown current (10 nA typical)
-Complete shutdown for TXD, RXD, and PIN diode
*Small module size
-2.70 x 9.10 x 3.65 mm (HxWxD)
*Withstands >100 mVp-p power supply ripple typically
*VCC supply 2.7 to 5.5 volts
*LED stuck-high protection
*IEC 825-Class 1 eye safe
*Designed to accommodate light loss with cosmetic windows

Applications
*Data communication
-PDAs
-Notebooks
-Printers
*Mobile telecom
-Cellular phones
-Pagers
-Smart phones
*Digital imaging
-Digital cameras
-Photo-imaging printers
*Electronic wallet
*Medical and industry data collection

HSDL-3000007, HSDL-3000017

Description
The ADNS-2051 is a low cost optical sensor used to implement a non-mechanical tracking engine for computer mice.
It is based on optical navigation technology, which measures changes in position by optically
acquiring sequential surface images (frames) and mathematically determining the direction and magnitude of movement.
The sensor is housed in a 16-pin staggered dual inline package (DIP) that is designed for use with the HDNS-2100 Lens and HDNS-2200 Clip and HLMP-ED80-XXXXX (639 nm LED illuminator source). There are no moving parts, and precision optical alignment is not required, facilitating high volume assembly.
The output format is two channel quadrature (X and Y direction) which emulates encoder phototransistors. The current X and Y information are also available in registers accessed via a serial port.
Default resolution is specified as 400 counts per inch (cpi), with rates of motion up to 14 inches
per second (ips).
Resolution can also be programmed to 800 cpi.
The part is programmed via a two wire serial port, through registers.

Features
*Precise optical navigation technology
*No mechanical moving parts
*Complete 2D motion sensor
*Serial interface and/or quadrature interface
*Smooth surface navigation
*Programmable frame speed up to 2300 frames per sec (fps)
*Accurate motion up to 14 ips
*800 cpi resolution
*High reliability
*High speed motion detector
*No precision optical alignment
*Wave solderable
*Single 5.0 volt power supply
*Shutdown pin for USB suspend mode operation
*Power conservation mode during times of no movement
*On chip LED drive with regulated current
*Serial port registers
–Programming
–Data transfer
*16-pin staggered dual inline package (DIP)

Applications
*Mice for desktop PCs, workstations, and portable PCs
*Trackballs
*Integrated input devices

ADNS-2051, ADNB-2050, ADNB-2051, HDNS-2100, HDNS-2200

Description
The HEDS-5700 series is a family of low cost, high performance, optical incremental encoders with mounted shafts and bushings. The HEDS-5700 is available with tactile feedback for hand operated panel mount applications, or with free spinning shaft for applications requiring a pre-assembled encoder for position sensing.
The encoder contains a collimated LED light source and special detector circuit which allows for high resolution, excellent encoding performance, long rotational life, and increased reliability. The unit outputs two digital waveforms which are 90 degrees out of phase to provide position and direction information. The HEDS-5740 Series provides a third Index Channel.
The HEDS-5700 is quickly and easily mounted to a front panel using the threaded bushing, or it
can be directly coupled to a motor shaft (or gear train) for position sensing applications.

Features
*Two Channel Quadrature Output with Optional Index Pulse
*Available with or without Static Drag for Manual or Mechanized Operation
*High Resolution – Up to 512 CPR
*Long Rotational Life, >1 Million Revolutions
*-20 to 85°C Operating Temperature Range
*TTL Quadrature Output
*Single 5 V Supply
*Available with Color Coded Leads

Applications
The HEDS-5700 with the static drag option is best suited for applications requiring digital information from a manually operated knob. Typical front panel applications include instruments, CAD/CAM systems, and audio/video control boards.
The HEDS-5700 without static drag (free spinning) is best suited for low speed, mechanized
operations. Typical applications are copiers, X-Y tables, and assembly line equipment.

HEDS-5700-K00, HEDS-5740-K00, HEDS-5701-K00, HEDS-5741-K00

Description
These chip LEDs are designed in an industry standard package for ease of handling and use. Five different LED colors are available in four compact, single color packages.
The HSMx-C150 has the industry standard 3.2 x 1.6 mm footprint that is excellent for all around use. The HSMx-C170 has the widely used 2.0 x 1.25 mm footprint. The HSMx-C190 has the industry standard 1.6 x 0.8 mm footprint, its low 0.8 mm profile and wide viewing angle make this LED exceptional for backlighting applications.
The HSMx-C110 is a rightangle package with the universally accepted dimensions of 3.2 x 1.0 x 1.5 mm. This part is ideal for LCD backlighting and sidelighting applications.
All packages are compatible with IR reflow solder processes. The small size and wide viewing angle make these LEDs prime choices for backlighting applications and front panel illumination especially where space is a premium.

Features
*Small Size
*Industry Standard Footprint
*Compatible with IR Solder
*Diffused Optics
*Operating Temperature Range of -30°C to +85°C
*Right Angle Package Available
*Five Colors Available
*Available in 8 mm Tape on 7 in. (178 mm) Diameter Reels

Applications
*Keypad Backlighting
*Push-Button Backlighting
*LCD Backlighting
*Symbol Backlighting
*Front Panel Indicator

HSMS-C150, HSMD-C150, HSMY-C150, HSMG-C150, HSMH-C150
HSMS-C170, HSMD-C170, HSMY-C170, HSMG-C170, HSMH-C170
HSMS-C190, HSMD-C190, HSMY-C190, HSMG-C190, HSMH-C190
HSMS-C110, HSMD-C110, HSMY-C110, HSMG-C110, HSMH-C110

Description
The HDNS-2100 Solid-State Optical Mouse Lens is designed for use with Agilent Optical Mouse Sensors and the illumination subsystem provided by the HDNS-2200 or HDNS-2200
#001 LED Assembly Clip and the HLMP-ED80 LED. Together with the LED, the HDNS-2100 provides the directed illumination and optical imaging necessary for proper operation of the Optical Mouse Sensor. The HDNS-2100 is a precision molded optical component and should be
handled with care to avoid scratching of the optical surfaces.

HDNS-2100 #001

DESCRIPTION
The HPND-4005 planar beam lead PIN diode is constructed to offer exceptional lead strength while achieving excellent electrical performance at high frequencies.
High beam strength offers users superior assembly yield, while extremely low capacitance allows high isolation to be realized.
Nitride passivation and polyimide coating provide reliable device protection.

FEATURES
*High Breakdown Voltage 120 V Typical
*Low Capacitance 0.017 pF Typical
*Low Resistance 4.7 W Typical
*Rugged Construction 4 Grams Minimum Lead Pull
*Nitride Passivated

APPLICATIONS
The HPND-4005 beam lead PIN diode is designed for use in stripline or microstrip circuits.
Applications include switching, attenuating, phase shifting, limiting, and modulating at microwave frequencies. The extremely low capacitance of the HPND-4005 makes it ideal for
circuits requiring high isolation in a series diode configuration.

Description
The ADNS-3040 is an ultra low-power optical navigation sensor.
It has a new, lowpower architecture and automatic power management modes, making it ideal for battery-and power-sensitive applications such as cordless input devices.
The ADNS-3040 is capable of high-speed motion detection – up to 20 ips and 8G.
In addition, it has an on-chip oscillator and LED driver to minimize external components.
The ADNS-3040 along with the ADNS-3120-001 lens, ADNS- 2220 clip and HLMP-ED80-
PS000 LED form a complete and compact mouse tracking system.
There are no moving parts, which means high reliability and less maintenance for the end user.
In addition, precision optical alignment is not required, facilitating high volume assembly.
The sensor is programmed via registers through a four-wire serial port. It is packaged in a
20-pin DIP.

Features
* Low power architecture
* Self-adjusting power-saving modes for longest battery life
* High speed motion detection up to 20 ips and 8G
* SmartSpeed self-adjusting frame rate for optimum performance
* Motion detect pin output
* Internal oscillator – no clock input needed
* Selectable 400 and 800 cpi resolution
* Wide operating voltage: 2.5V-3.6V nominal
* Four wire serial port
* Minimal number of passive components

Applications
* Optical Mice
* Optical trackballs
* Integrated input devices
* Battery-powered input devices

ADNS3040