General Description
The HMC-VVD102 is a monolithic GaAs PIN diode ased Voltage Variable Attenuator (VVA) which exhibits low insertion loss, high IP3 and wide dynamic range. All bond pads and the die backside are Ti/Au metallized and the PIN diode devices are fully passivated for reliable operation. This wideband MMIC VVA is compatible with conventional die attach methods, as well as thermocompression and thermosonic wirebonding, making it ideal for MCM and hybrid microcircuit applications. All data shown herein is measured with the chip in a 50 Ohm environment and contacted with RF probes

Features
*Low Insertion Loss: 1.5 dB
*Wide Dynamic Range: 18 dB
*High Input IP3: +17 dBm
*Analog Control Voltage: -4 to +4V
*Die Size: 1.01 x 1.175 x 0.1 mm

Typical Applications
This HMC-VVD102 is ideal for:
*Point-to-Point Radios
*Point-to-Multi-Point Radios
*Military Radios, Radar & ECM
*Test Equipment & Sensors
*Space

댓글을 달아 주세요 Comment

DESCRIPTION
The LTM®8027 is a complete 4A, DC/DC step-down power supply. Included in the package are the switching controller, power switches, inductor and all support components. Operating over an input voltage range of 4.5V to 60V (7.5V minimum voltage to start), the LTM8027 supports output voltages up to 24V, and a switching frequency range of 100kHz to 500kHz, each set by a single resistor. Only the bulk input and output fi lter capacitors are needed to fi nish the design.
The low profi le package (4.32mm) enables utilization of unused space on the bottom of PC boards for high density point of load regulation. A built-in soft-start timer is adjustable with a small capacitor.
The LTM8027 is packaged in a thermally enhanced, compact (15mm × 15mm) and low profi le (4.32mm) over-molded land grid array (LGA) package suitable for automated assembly by standard surface mount equipment. The LTM8027 is Pb-free and RoHS compliant.

FEATURES
*Complete Switch Mode Power Supply
*Wide Input Voltage Range: 4.5V to 60V (7.5V Minimum Voltage to Start)
*Wide Output Voltage Range: 2.5V to 24V (See Table 2)
*4A Output Current
*Programmable Soft-Start
*10μA Shutdown Supply Current
*Selectable Switching Frequency Current Mode Control
*Up to 95% Effi ciency
*Pb-Free (e4) RoHS Compliant Package with Gold Pad Finish
*Tiny, Low Profi le (15mm × 15mm × 4.32mm) Surface Mount LGA Package

APPLICATIONS
*12V and 42V Automotive and Heavy Equipment
*48V Telecom Power Supplies
*Avionics and Industrial Control Systems
*Distributed Power Converters

LTM8027EVPBF, LTM8027IVPBF, LTM8027MPVPBF, LTM8027EV, LTM8027IV

댓글을 달아 주세요 Comment

DESCRIPTION
The GAL22LV10D, at 4 ns maximum propagation delay time, provides the highest speed performance available in the PLD market. The GAL22LV10C can interface with both 3.3V and 5V signal levels. The GAL22LV10 is manufactured using Lattice Semiconductor's advanced 3.3V E2CMOS process, which combines CMOS with Electrically Erasable (E2) floating gate technology.
High speed erase times (<100ms) allow the devices to be reprogrammed quickly and efficiently.
The generic architecture provides maximum design flexibility by allowing the Output Logic Macrocell (OLMC) to be configured by the user.
Unique test circuitry and reprogrammable cells allow complete AC, DC, and functional testing during manufacture. As a result, Lattice Semiconductor delivers 100% field programmability and
functionality of all GAL products. In addition, 100 erase/write cycles and data retention in excess of 20 years are specified.

FEATURES
*HIGH PERFORMANCE E2CMOS® TECHNOLOGY
-4 ns Maximum Propagation Delay
-Fmax = 250 MHz
-3 ns Maximum from Clock Input to Data Output
-UltraMOS® Advanced CMOS Technology
*3.3V LOW VOLTAGE 22V10 ARCHITECTURE
-JEDEC-Compatible 3.3V Interface Standard
-5V Compatible Inputs
-I/O Interfaces with Standard 5V TTL Devices (GAL22LV10C)
*ACTIVE PULL-UPS ON ALL PINS (GAL22LV10D)
*E2 CELL TECHNOLOGY
-Reconfigurable Logic
-Reprogrammable Cells
-100% Tested/100% Yields
-High Speed Electrical Erasure (<100ms)
-20 Year Data Retention
*TEN OUTPUT LOGIC MACROCELLS
-Maximum Flexibility for Complex Logic Designs
-Programmable Output Polarity
*PRELOAD AND POWER-ON RESET OF ALL REGISTERS
-100% Functional Testability
*APPLICATIONS INCLUDE:
-Glue Logic for 3.3V Systems
-DMA Control
-State Machine Control
-High Speed Graphics Processing
-Standard Logic Speed Upgrade
*ELECTRONIC SIGNATURE FOR IDENTIFICATION 22LV10D

GAL22LV10D-4LJ, GAL22LV10D-5LJ, GAL22LV10C-7LJ, GAL22LV10C-10LJ

댓글을 달아 주세요 Comment

Description
The source color devices are made with InGaN on SiC Light Emitting Diode.
Static electricity and surge damage the LEDS.
It is recommended to use a wrist band or anti-electrostatic glove when handling the LEDs.
All devices, equipment and machinery must be electrically grounded.

Features
*2.0mmx1.25mm SMT LED, 0.75mm THICKNESS.
*LOW POWER CONSUMPTION.
*WIDE VIEWING ANGLE.
*IDEAL FOR BACK LIGHT AND INDICATOR.
*VARIOUS COLORS AND LENS TYPES AVAILABLE.
*PACKAGE : 2000PCS / REEL.
*MOISTURE SENSITIVITY LEVEL : LEVEL 4.
*ELECTROSTATIC DISCHARGE THRESHOLD (HBM):1000V.
*TYP. COLOR TEMPERATURE:6500K
*COLOR COORDINATES:X=0.31,Y=0.31 ACC. TO CIE1931(WHITE).
*OPTICAL EFFICIENCY:26 lm/W(TYP.)
*COLOR REPRODUCTION INDEX:80
*RoHS COMPLIANT.

Applications
*traffic signaling.
*backlighting (illuminated advertising , general lighting).
*interior and exterior automotive lighting.
*substitution of micro incandescent lamps.
*reading lamps.
*signal and symbol luminaire for orientation.
*marker lights (e.g. steps, exit ways, etc).
*decorative and entertainment lighting.
*indoor and outdoor commercial and residential architectural lighting.

APTK2012RWC/Z-F01
TAG Chip, lamp, led, SMD

댓글을 달아 주세요 Comment

General Description
The MX884 targets power management applications where high noise immunity and low cost are primary requirements. Its integrated 10-bit ADC provides high resolution, making it ideal for current monitoring systems. The MX884 enables digital power management, in which a microcontroller can readily monitor the current in a system and perform other control functions in power systems and motion control products.
The MX884 converts a small voltage developed across an external “current” sense resistor to a 10-bit digital output. It features a wide common mode input supply voltage range of 3V to 60V and easily interfaces to most microcontrollers. The design is simple yet cost-effective, requiring very few external components, making it especially suitable for high volume applications.

Features
*3-60 V Operating Voltage Range
*Integrated 10-bit ADC
*3 wire serial interface
*Microcontroller Compatible
*Low Power
*Minimum External Components
*TSOT-23 RoHS Compliant Package

Applications
*Lighting Management
*Current Shunt Measurement
*Remote Sensing
*Battery Monitoring
*Microprocessor Controlled Power Management

MX884HTTR

댓글을 달아 주세요 Comment

Description
The EL5411T is a high voltage rail-to-rail input-output amplifier with low power consumption. The EL5411T contains four amplifiers. Each amplifier exhibits beyond the rail input capability, rail-to-rail output capability and is unity gain stable.
The maximum operating voltage range is from 4.5V to 19V. It can be configured for single or dual supply operation, and typically consumes only 3mA per amplifier. The EL5411T has an output short circuit capability of ±300mA and a continuous output current capability of ±70mA.
The EL5411T features a high slew rate of 100V/μs, and fast settling time. Also, the device provides common mode input capability beyond the supply rails, rail-to-rail output capability, and a bandwidth of 60MHz (-3dB). This enables the amplifiers to offer maximum dynamic range at any supply voltage. These features make the EL5411T an ideal amplifier solution for use in TFT-LCD panels as a VCOM driver or static gamma buffer, and in high speed filtering and signal conditioning applications. Other applications include battery power and portable devices, especially where low power consumption is important.
The EL5411T is available in a 14 Ld HTSSOP and a space saving thermally enhanced 16 Ld 4mmx4mm TQFN package. The device operates over an ambient temperature range of -40°C to +85°C.

Features
*60MHz (-3dB) Bandwidth
*4.5V to 19V Maximum Supply Voltage Range
*100V/μs Slew Rate
*3mA Supply Current (per Amplifier)
*±70mA Continuous Output Current
*±300mA Output Short Circuit Current
*Unity-gain Stable
*Beyond the Rails Input Capability
*Rail-to-rail Output Swing
*Built-in Thermal Protection
*-40°C to +85°C Ambient Temperature Range
*Pb-Free (RoHS Compliant)

Applications
*TFT-LCD Panels
*VCOM Amplifiers
*Static Gamma Buffers
*Drivers for A/D Converters
*Data Acquisition
*Video Processing
*Audio Processing
*Active Filters
*Test Equipment
*Battery-powered Applications
*Portable Equipment

EL5411TIREZ, EL5411TIREZ-T7, EL5411TIREZ-T13, EL5411TILZ, EL5411TILZ-T7

댓글을 달아 주세요 Comment

DESCRIPTION
The MS5541C is the miniature version of MS5535C pressure sensor module. It contains a precision piezoresistive pressure sensor and an improved version of the 16 Bit Micropower Sensor interface IC known from the MS5535C. Compared to the previous version the ESD sensitivity has been improved to 4kV on all pins. In addition to this the MS5541C is from its outer dimensions compatible to the MS54xx series of pressure sensors. It uses an antimagnetic polished stainless steel ring for sealing with O-ring. The sensor provides 16 Bit pressure and temperature data via a 3 wire serial interface that can be easily interfaced with 4 Bit low power microcontrollers. 64 Bit of factory programmed PROM provides calibration data for a highly accurate pressure and temperature calculation. The MS5541C is fully software compatible to the MS5535C and previous versions of MS5541.

FEATURES
*Resolution 1.2 mbar
*Supply voltage 2.2 V to 3.6 V
*Operating current < 5uA
*Standby current < 0.1uA
*-40°C to +85°C
*No external components required

APPLICATIONS
*Diving computers and divers watches
*Mobile water depth measurement systems

MS5541-CM

댓글을 달아 주세요 Comment

Description
The IRS2609D is a high voltage, high speed power MOSFET and IGBT drivers with dependent high and low side referenced output channels. Proprietary HVIC and latch immune CMOS technologies enable ruggedized monolithic construction. The logic input is compatible with Standard CMOS or LSTTL output, down to 3.3 V logic. The output drivers feature a high pulse current buffer stage designed for minimum driver cross-conduction. The floating channel can be used to drive an N-channel power MOSFET or IGBT in the high side configuration which operates up to 600 V.

Features
*Floating channel designed for bootstrap operation
-Fully operational to +600 V
-Tolerant to negative transient voltage – dV/dt immune
*Gate drive supply range from 10 V to 20 V
*Undervoltage lockout for both channels
*3.3 V, 5 V and 15 V input logic compatible
*Cross-conduction prevention logic
*Matched propagation delay for both channels
*High side output in phase with IN input
*Internal 530 ns dead-time
*Lower di/dt gate driver for better noise immunity
*Shut down input turns off both channels
*Integrated bootstrap diode
*RoHS compliant

Applications
*Air Conditioner
*Micro/Mini Inverter Drives
*General Purpose Inverters
*Motor Control

IRS2609DSTRPbF

댓글을 달아 주세요 Comment

Description
The IDTAS4624 low on-resistance (RON), low voltage, single-pole/double-throw (SPDT) analog switch operates from a single +1.8 V to +5.5 V supply. The IDTAS4624 features a 0.5Ω (max) RON for its NC switch and a 0.8Ω (max) RON for its NO switch at a +2.7 V supply. It also features break-before-make switching action (2 ns) with tON = 50 ns and tOFF = 40 ns at +3 V. The digital logic input is 1.8 V logic-compatible with a +2.7 V to +3.3 V supply.

Features
*+1.8 V to +5.5 V single-supply operation
*Rail-to-rail signal handling
*1.8 V logic compatibility
*RON match between channels: 0.06Ω (max)
*RON flatness over signal range: 0.15Ω (max)
*NC Switch RON: 0.5Ω max (+2.7 V Supply)
*NO Switch RON: 0.8Ω max (+2.7 V Supply)
*Low crosstalk: -68dB (100 kHz)
*High Off-isolation: -64dB (100 kHz)
*THD: 0.03%
*50 nA (max) supply current
*Low leakage currents: 1 nA (max) at TA = +25°C
*6-pin SOT-23 package

Applications
*Speaker headset switching
*MP3 players
*Battery-operated equipment
*Audio and video signal routing
*PCMCIA cards
*Cellular phones
*Modems

AS4624DZG8

댓글을 달아 주세요 Comment

Description
The LXT362 is a fully integrated, combination transceiver for T1 ISDN Primary Rate Interface and general T1 long and short haul applications. It operates over 22 AWG twisted-pair cables from 0 to 6 kft and offers Line Build Outs and pulse equalization settings for all T1 Line Interface Unit (LIU) applications.
LXT362 provides both a serial port for microprocessor control (Host mode) as well as standalone operation (Hardware mode). The device incorporates advanced crystal-less digital jitter attenuation in either the transmit or receive data path starting at 3 Hz. B8ZS encoding/decoding and unipolar or bipolar data I/O are selectable. Loss of signal monitoring and a variety of diagnostic loopback modes can also be selected.

Product Features
*Fully integrated transceiver for Long or Short-Haul T1 interfaces
-Crystal-less digital jitter attenuation
-Select either transmit or receive path
*No crystal or high speed external clock required
*Meets or exceeds specifications in ANSI T1.102, T1.403 and T1.408; and AT&T Pub 62411
*Supports 100 Ω (T1 twisted-pair) applications
*Selectable receiver sensitivity – fully restores the received signal after transmission through a cable with attenuation of either 0 to 26 dB, or 0 to 36 dB @ 772 kHz
*Five Pulse Equalization Settings for T1 short-haul applications
*Four Line Build-Outs for T1 long-haul applications from 0 dB to -22.5 dB
*Transmit/receive performance monitors with Driver Fail Monitor Open and Loss of Signal outputs
*Selectable unipolar or bipolar data I/O and B8ZS encoding/decoding
*Line attenuation indication output in 2.9 dB steps
*QRSS generator/detector for testing or monitoring
*Local, remote, and analog loopback, plus in-band network loopback code generation and detection
*Multiple register serial interface for microprocessor control
*Available in 28-pin PLCC, 44-pin PQFP, and 44-pin LQFP packages

Applications
*ISDN Primary Rate Interface (ISDN PRI)
*CSU/NTU interface to T1 Service
*Wireless Base Station interface
*T1 LAN/WAN bridge/routers
*T1 Mux; Channel Banks
*Digital Loop Carrier - Subscriber Carrier Systems

249033-001

댓글을 달아 주세요 Comment