Description
The AP1250CMP is a simple, cost-effective and high-speed linear regulator designed to generate termination voltage in double data rate (DDR) memory system to comply with the JEDEC SSTL_2 and SSTL_18 or other specific interfaces such as HSTL, SCSI-2 and SCSI-3 etc. devices requirements. The regulator is capable of actively sinking or sourcing up to 2A while regulating an output voltage to within 40mV. The output termination voltage cab be tightly regulated to track 1/2VDDQ by two external voltage divider resistors or the desired output voltage can be pro-grammed by externally forcing the REFEN pin voltage.
The AP1250CMP also incorporates a high-speed differential amplifier to provide ultra-fast response in line/load transient. Other features include extremely low initial offset voltage, excellent load regulation, current limiting in bi-directions and on-chip thermal shut-down protection.
The AP1250CMP are available in the ESOP-8 (Exposed Pad) surface mount packages.

Features
*Ideal for DDR-I, DDR-II and DDR-III VTT Applications
*Sink and Source 2A Continuous Current
*Integrated Power MOSFETs
*Generates Termination Voltage for SSTL_2, SSTL_18, HSTL, SCSI-2 and SCSI-3 Interfaces.
*High Accuracy Output Voltage at Full-Load
*Output Adjustment by Two External Resistors
*Low External Component Count
*Shutdown for Suspend to RAM (STR) Functionality with High-Impedance Output
*Current Limiting Protection
*On-Chip Thermal Protection
*Available in ESOP-8 (Exposed Pad) Packages
*VIN and VCNTL No Power Sequence Issue
*RoHS Compliant and 100% Lead (Pb)-Free

Application
*Desktop PCs, Notebooks, and Workstations
*Graphics Card Memory Termination
*Set Top Boxes, Digital TVs, Printers
*Embedded Systems
*Active Termination Buses
*DDR-I, DDR-II and DDR-III Memory Systems

Trackback :: http://datasheetblog.com/trackback/2885

댓글을 달아 주세요 Comment

GENERAL DESCRIPTION
The LP2950 and LP2951 are micropower voltage regulators ideally suited for use in battery-powered systems. These devices feature very low quiescent current (typ.75μA), and very low dropout voltage (typ.45mV at light loads and 380mV at 100mA) thus prolonging battery life. The quiescent current increases only slightly in dropout. The LP2950/LP2951 has positive transient protection up to 60V and can survive unregulated input transient up to 20V below ground.
The LP2950 and LP2951 were designed to include a tight initial tolerance (typ. 0.5%), excellent load and line regulation (typ. 0.05%), and a very low output voltage temperature coefficient, making these devices useful as a low-power voltage reference. The LP2950 is offered in the 3-pin TO-92 package. LP2951 is available in 8-pin plastic SOIC and DIP packages and offers three major additional system features. An error flag output warns of a low output voltage, often due to failing batteries on input. The LP2951 also features the logic-compatible shutdown input which enables the regulator to be switched on and off.
The LP2951 device may be pin-strapped for a 5V, 3.3V, or 3V output, or programmed from 1.24V to 29V with an external pair of resistors.

FEATURES
*5V, 3.3V, and 3V Versions at 100mA Output Current
*High Accuracy Output Voltage
*Extremely Low Quiescent Current
*Low Dropout Voltage
*Extremely Tight Load and Line Regulation
*Very Low Temperature Coefficient
*Current and Thermal Limiting
*Needs Minimum Capacitance (1μF) for Stability
*Unregulated DC Positive Transients 60V
ADDITIONAL FEATURES (LP2951 ONLY)
*1.24V to 29V Programmable Output
*Error Flag Warning of Voltage Output Dropout
*Logic Controlled Electronic Shutdown

APPLICATIONS
*Battery Powered Systems
*Portable Consumer Equipment
*Cordless Telephones
*Portable (Notebook) Computers
*Portable Instrumentation
*Radio Control Systems
*Automotive Electronics
*Avionics
*Low-Power Voltage Reference

LP2951, LP2950ACN-X, LP2950CN-X, LP2951ACP-X, LP2951CP-X

Trackback :: http://datasheetblog.com/trackback/2884

댓글을 달아 주세요 Comment

GENERAL DESCRIPTION
The ALD1702/ALD1703 is a monolithic operational amplifier intended primarily for a wide range of analog applications in +5V single power supply and ±5V dual power supply systems as well as +4V to +12V battery operated systems. All device characteristics are specified for +5V single supply or ±2.5V dual supply systems. It is manufactured with Advanced Linear Devices' enhanced ACMOS silicon gate CMOS process.
The device is designed to offer a balanced trade-off of performance parameters providing a wide range of desired specifications. It offers the industry pin configuration of mA741 and ICL7611 types.
The ALD1702/ALD1703 has been developed specifically with the 5V single supply or ±2.5 dual supply user in mind. Several important characteristics of the device make many applications easy to implement for these supply voltages. First, the operational amplifier can operate with rail to rail input and output voltages. This feature allows numerous analog serial stages to be implemented without losing operating voltage margin. Secondly, the device was designed to accommodate mixed applications where digital and analog circuits may work off the same 5V power supply. Thirdly, the output stage can drive up to 400pF capacitive and 5KW resistive loads in non-inverting unity gain connection and double the capacitance in the inverting unity gain mode.
These features, coupled with extremely low input currents, high voltage gain, useful bandwidth of 1.5MHz, slew rate of 2.1V/ms, low power dissipation, low offset voltage and temperature drift, make the ALD1702/ALD1703 a truly versatile, user friendly, operational amplifier.
The ALD1702/ALD1703 is designed and fabricated with silicon gate CMOS technology, and offers 1pA typical input bias current. On-chip offset voltage trimming allows the device to be used without nulling in most applications. The device offers typical offset drift of less than 7mV/°C which eliminates many trim or temperature compensation circuits. For precision applications, the ALD1702 is designed to settle to 0.01% in 8ms.

FEATURES
*Rail-to-rail input and output voltage ranges
*All parameters specified for +5V single supply or ±2.5V dual supply systems.
*High load capacitance capability -- 4000pF typical
*No frequency compensation required -- unity gain stable
*Extremely low input bias currents -- 1.0pA typical (30pA max.)
*Ideal for high source impedance applications
*Dual power supply ±2.5V to ±5.0V operation
*Single power supply +5V to +12V operation
*High voltage gain -- typically 85V/mV @ ±2.5V and 250V/mV @ ±5.0V
*Drive as low as 2KW load with 5mA drive current
*Output short circuit protected
*Unity gain bandwidth of 1.5MHz (1.0MHz min.)
*Slew rate of 2.1V/ms (1.4V/ms min.)
*Low power dissipation

APPLICATIONS
*Voltage amplifier
*Voltage follower/buffer
*Charge integrator
*Photodiode amplifier
*Data acquisition systems
*High performance portable instruments
*Signal conditioning circuits
*Sensor and transducer amplifiers
*Low leakage amplifiers
*Active filters
*Sample/Hold amplifier
*Picoammeter
*Current to voltage converter
*Coaxial cable driver

ALD1702ADA, ALD1702ASA, ALD1702APA, ALD1702BDA, ALD1702BSA, ALD1702BPA

Trackback :: http://datasheetblog.com/trackback/2883

댓글을 달아 주세요 Comment

General Description
The AAT2848 is a tri-mode charge pump optimized for systems operating with lithium-ion/polymer batteries. The charge pump provides power for both white LED backlight and flash, with an integrated four channel backlight LED current sink plus two channel flash LED current sinks.
Each backlight channel can drive up to 30mA, while each flash current sink/channel can drive up to 300mA (600mA total). Two independent S2Cwire™ (AnalogicTech’s Simple Serial Control™) serial digital interface inputs enable, disable, and set LED current to one of 32 levels for the backlight and to one of 16 levels for the flash, with fullscale current independently set for backlight and flash using external resistors.
The AAT2848 offers a built-in fade-in/out function for linear control of the backlight current during ON/OFF transitions. The fade time is programmable by an external capacitor.
The AAT2848 also offers a built-in flash timeout function as a safety feature associated with the high power flash driver. The safety timer is also programmable via an external capacitor.
The AAT2848 is equipped with built-in short-circuit and over-temperature protection. The soft-start circuitry prevents excessive inrush current at start-up and mode transitions. The AAT2848 is available in a Pb-free, space saving TQFN33-20 package and operates over the -40°C to +85°C ambient temperature range.

Features
*Tri-Mode (1x/1.5x/2x) Charge Pump
*Four 30mA Backlight LED Channels
*Independent S2Cwire Control for Backlight
*32-Level Programmable Backlight Current Control—Linear, Inverting
*Two 300mA Flash LED Channels
*Independent S2Cwire Control for Flash
*16-Level Programmable Flash Current Control—Linear, Inverting
*User-Programmable Full Scale Current for Backlight and Flash
*User-Programmable Fade-In/Fade-Out Function for Backlight
*User-Programmable Safety Timer for Flash LED Protection
*Built-In Thermal Protection
*Automatic Soft-Start
*-40°C to +85°C Temperature Range
*Available in TQFN33-20 Package

Applications
*Camera Enabled Mobile Devices
*Digital Still Cameras
*Multimedia Mobile Phones

AAT2848IDG-T1
TAG Display, Flash

Trackback :: http://datasheetblog.com/trackback/2882

댓글을 달아 주세요 Comment

GENERAL DESCRIPTION
The ACT4012A is a current-mode step-down DC/DC converter that generates up to 1.5A output 420kHz switching frequency. The device utilizes Active-Semi’s proprietary ISOBCD20 process for operation with input voltages up to 20V.
Consuming only 10μA in shutdown mode, the ACT4012A is highly efficient with peak efficiency at 94% when in operation. Protection features include cycle-by-cycle current limit, thermal shutdown, and frequency foldback at short circuit.
The ACT4012A is available in a SOP-8 package and requires very few external devices for operation.

FEATURES
*1.5A Output Current
*Up to 94% Efficiency
*Up to 20V Input Range
*10μA Shutdown Supply Current
*420kHz Switching Frequency
*Adjustable Output Voltage
*Cycle-by-Cycle Current Limit Protection
*Thermal Shutdown Protection
*Frequency Foldback at Short Circuit
*Stability with Wide Range of Capacitors, Including Low ESR Ceramic Capacitors
*SOP-8 Package

APPLICATIONS
*TFT LCD Monitors
*Portable DVDs
*Car-Powered or Battery-Powered Equipments
*Set-Top Boxes
*Telecom Power Supplies
*DSL and Cable Modems and Routers
*Termination Supplies

ACT4012ASH, ACT4012ASH-T

Trackback :: http://datasheetblog.com/trackback/2881

댓글을 달아 주세요 Comment

DESCRIPTION
The AZ10/100LVEL16 is a differential receiver. The device is functionally equivalent to the E116 device with higher performance capabilities. With output transition times significantly faster than the E116, the LVEL16 is ideally suited for interfacing with high frequency sources.
The LVEL16 provides a VBB output for single-ended use or a DC bias reference for AC coupling to the device. For single-ended input applications, the VBB reference should be connected to one side of the D/D¯ differential input pair. The input signal is then fed to the other D/D¯ input. The VBB pin can support 1.5 mA sink/source current. When used, the VBB pin should be bypassed to ground via a 0.01 μF capacitor.
Under open input conditions internal input clamps will force the Q output LOW.

FEATURES
*Green and RoHS Compliant / Lead (Pb) Free Packages available
*250ps Propagation Delay
*High Bandwidth Output Transitions
*Operating Range of 3.0V to 5.5V
*Internal Input Pulldown Resistors
*Direct Replacement For ON Semiconductor MC10EL16, MC100EL16, & MC100LVEL16
*IBIS Model Files Available on Arizona Microtek Website

AZ10LVEL16D, AZ100LVEL16D, AZ10LVEL16T, AZ100LVEL16T, AZ100LVEL16NG

Trackback :: http://datasheetblog.com/trackback/2880

  1. Subject: Fortnite esp

    Tracked from Fortnite esp 2019/11/02 19:10  삭제

    DATASHEETBLOG

댓글을 달아 주세요 Comment

General Description
The ICS1893BY-10 is a low-power, physical-layer device (PHY) that supports the ISO/IEC 10Base-T and 100Base-TX Carrier-Sense Multiple Access/Collision Detection (CSMA/CD) Ethernet standards. The ICS1893BY-10 supports managed or unmanaged node, repeater, and switch applications.
The ICS1893BY-10 is intended for MII, Node applications that require the Auto-MIDIX feature that automatically corrects crossover errors in plant wiring.
The ICS1893BY-10 incorporates digital signal processing (DSP) in its Physical Medium Dependent (PMD) sublayer. As a result, it can transmit and receive data on unshielded twisted-pair (UTP) category 5 cables with attenuation in excess of 24 dB at 100 MHz. With this ICS-patented technology, the ICS1893BY-10 can virtually eliminate errors from killer packets.
The ICS1893BY-10 provides a Serial Management Interface for exchanging command and status information with a Station Management (STA) entity.
The ICS1893BY-10 Media Dependent Interface (MDI) can be configured to provide either half- or full-duplex operation at data rates of 10 MHz or 100 MHz. The MDI configuration can be established manually (with input pins or control register settings) or automat i c a l l y (using the Auto-Negotiation features). When the ICS1893BY-10 Auto-Negotiation sublayer is enabled, it exchanges technology capability data with its remote link partner and automatically selects the highest-performance operating mode they have in common.

Features
*Supports category 5 cables with attenuation in excess of 24 dB at 100 MHz
*Fully integrated, DSP-based PMD includes:
-Adaptive equalization and baseline wander correction
-Transmit wave shaping and stream cipher scrambler
-MLT-3 encoder and NRZ/NRZI encoder
*Low-power, 0.35-micron CMOS (typically 400 mW)
*Power-down mode typically 21mW
*Single 3.3-V power supply.
*Single-chip, fully integrated PHY provides PCS, PMA, PMD, and AUTONEG sublayers of IEEE standard
*10Base-T and 100Base-TX IEEE 802.3 compliant
*Highly configurable design supports:
-Node, repeater, and switch applications
-Managed and unmanaged applications
-10M or 100M half- and full-duplex modes
-Parallel detection
-Auto-negotiation, with Next Page capabilities
-Auto-MDI/MDIX crossover correction
*MAC/Repeater Interface can be configured as:
-10M or 100M Media Independent Interface
-100M Symbol Interface (bypasses the PCS)
-10M 7-wire Serial Interface
*Clock and crystal supported
*Small Footprint 64-pin Thin Quad Flat Pack (TQFP)
*Available in Industrial Temperature and Lead-Free

ICS1893BYI-10, ICS1893BY-10LF, ICS1893BYI-10LF

Trackback :: http://datasheetblog.com/trackback/2879

댓글을 달아 주세요 Comment

DESCRIPTION
The CAT6218 is a 300mA CMOS low dropout regulator that provides fast response time during load current and line voltage changes.
The quick-start feature allows the use of an external bypass capacitor to reduce the overall output noise without affecting the turn-on time of just 150μs.
With zero shutdown current and low ground current of 55μA typical, the CAT6218 is ideal for batteryoperated devices with supply voltages from 2.3V to 5.5V. An internal under voltage lockout circuit disables the output at supply voltages under 2.1V typical.
The CAT6218 offers 1% initial accuracy and low dropout voltage, 180mV typical at 300mA. Stable operation is provided with a small value ceramic capacitor, reducing required board space and compo–nent cost.
Other features include fold-back current current limit and thermal protection.
The device is available in the low profile (1mm max height) 5-lead thin SOT23 package.

FEATURES
*Guaranteed 300mA output current
*Low dropout voltage of 180mV typical at 300mA
*Stable with 1μF ceramic output capacitor
*External 10nF bypass capacitor for low noise
*Quick-start feature
*No-load ground current of 55μA typical
*Full-load ground current of 80μA typical
*±1.0% output voltage initial accuracy
*±2.0% accuracy over temperature
*“Zero” current shutdown mode
*Fold-back current limit and under-voltage lockout
*Thermal protection
*Thin SOT23-5 package

APPLICATIONS
*Cellular phones
*Battery-powered devices
*Consumer Electronics

CAT6218-180TD-GT3, CAT6218-240TD-GT3, CAT6218-270TD-GT3

Trackback :: http://datasheetblog.com/trackback/2878

댓글을 달아 주세요 Comment

DESCRIPTION
converter delivering high efficiency in a SOT23-6 package. The device has an internal NMOS switch and PMOS synchronous rectifier and has the capacity of supplying 3.3V at 100mA from a single AA cell input.
High frequency switching (up to 2MHz) minimizes the board area by allowing the use of tiny, low profile inductors and ceramic capacitors.
The KB3436 provides automatic pulse skipping at light loads, thus reducing the supply current for extended battery life. At shutdown, the KB3436 fully discharges the output to ground and draws no supply current.
The KB3436 is available in small SOT23-6 package with both fixed and adjustable output voltage versions.

FEATURES
*Up to 96% efficiency
*Low start-up voltage 0.8V
*Internal synchronous rectifier
*Up to 2MHz switching allows for tiny external components
*0.5V to 4.4V input range
*2.5V to 5.0V output range (Note 3)
*Feedback Voltage: 1.00V +/-2%
*Logic controlled shutdown (<1μA)
*Low 250μA operating supply current (measured at VOUT)
*Pulse skipping at light load for extended battery life
*Generates 3.3V at 100mA from single AA cell
*Stable with ceramic output capacitor
*Low profile 6-Leads SOT23-6 package

APPLICATIONS
*PDAs and organizers
*Digital cameras
*Wireless mice/ keyboards
*Portable medical equipment
*Cordless phones
*Wireless Headsets

Trackback :: http://datasheetblog.com/trackback/2877

댓글을 달아 주세요 Comment

Description
The transmitter module is intended for use at SDH and SONET bit rates. The device meets the intention of the ITU-T (G.691) recommendations.
The single silicon IC is used as a laser driver, modulator and automatic power control. To ensure a proper laser operation over the wide temperature range and life of operation, the average optical output power is controlled. The laser bias is externally accessible for monitoring of the performance. A power alarm is activated when the average optical power cannot be maintained within specification. A laser shut-down is also provided according to SDH/SONET requirements.

Key Features
*Provides 1620 nm supervisory channel laser source for WDM applications according to ITU-T draft G.691
*Average power control
*Small size (40x70x9 mm)
*CMOS alarm output
*Thermoelectric cooler included
*P-ECL data inputs
*Tone modulation input
*Single 5.0 V supply

Applications
*1620 nm supervisory channel applications in WDM systems

Trackback :: http://datasheetblog.com/trackback/2876

댓글을 달아 주세요 Comment