Description
The MC13028A is a third generation C–QUAM stereo decoder targeted for use in low voltage, low cost AM/FM E.T.R. radio applications. Advanced features include a signal quality detector that analyzes signal strength, signal to noise ratio, and stereo pilot tone before switching to the stereo mode. A “blend function” much like FM stereo has been added to improve the transition from mono to stereo. The audio output level is adjustable to allow easy interface with a variety of AM/FM tuner chips. The external components have been minimized to keep the total system cost low.

Features
*Adjustable Audio Output Level
*Stereo Blend Function
*Stereo Threshold Adjustment
*Operation from 2.2 V to 12 V Supply
*Precision Pilot Tone Detector
*Forced Mono Function
*Single Pinout VCO
*IF Amplifier with IF AGC Circuit
*VCO Shutdown Mode at Weak Signal Condition

MC13028AD, MC13028AP

DESCRIPTION
The MP2307 is a monolithic synchronous buck regulator. The device integrates 100mΩ MOSFETS that provide 3A of continuous load current over a wide operating input voltage of 4.75V to 23V. Current mode control provides fast transient response and cycle-by-cycle current limit.
An adjustable soft-start prevents inrush current at turn-on and in shutdown mode, the supply current drops below 1μA.
This device, available in an 8-pin SOIC package, provides a very compact system solution with minimal reliance on external components.

FEATURES
*3A Continuous Output Current, 4A Peak Output Current
*Wide 4.75V to 23V Operating Input Range
*Integrated 100mΩ Power MOSFET Switches
*Output Adjustable from 0.925V to 20V
*Up to 95% Efficiency
*Programmable Soft-Start
*Stable with Low ESR Ceramic Output Capacitors
*Fixed 340KHz Frequency
*Cycle-by-Cycle Over Current Protection
*Input Under Voltage Lockout
*Thermally Enhanced 8-Pin SOIC Package

APPLICATIONS
*Distributed Power Systems
*Networking Systems
*FPGA, DSP, ASIC Power Supplies
*Green Electronics/Appliances
*Notebook Computers

MP2307DN, EV2307DN-00A

Outline
This IC is a system reset IC developed using the CMOS process. Super low consumption current of 0.25μA typ. has been achieved through use of the CMOS process. Also, detection voltage is high precision detection of ±2%.

Features
*Super low consumption current 0.25μA typ. (when VDD = Vs + 1V)
*High precision detection voltage ±2%
*Hysteresis characteristic 5% typ.
*Operating range 0.95 ~ 10V
*Wide operating temperature range -30 ~ +85°C
*Detection voltage 2 ~ 6V (0.1V step)

Applications
*Microcomputer, CPU, MPU reset circuits
*Logic circuit reset circuits
*Battery voltage check circuits
*Back-up circuit switching circuits
*Level detection circuits

PST3120, PST3220, PST3320, PST3420

DESCRIPTION
M63816P/FP/KP are eight-circuit Single transistor arrays with clamping diodes. The circuits are made of NPN transistors. Both the semiconductor integrated circuits perform high-current driving with extremely low input-current supply.

FEATURES
*Three package configurations (P, FP, and KP)
*Medium breakdown voltage (BVCEO ³ 35V)
*Synchronizing current (IC(max) = 300mA)
*With clamping diodes
*Low output saturation voltage
*Wide operating temperature range (Ta = –40 to +85°C)

APPLICATION
Driving of digit drives of indication elements (LEDs and lamps) with small signals

M63816FP, M63816KP

General Description
Mimix Broadband’s 17.0-25.0 GHz GaAs packaged receiver has a noise figure of 2.5 dB and 20.0 dB image rejection across the band. This device is a two stage balanced LNA followed by an image reject sub-harmonic anti-parallel diode mixer and includes an integrated LO buffer amplifer. The image reject mixer eliminates the need for a bandpass filter after the LNA to remove thermal noise at the image frequency. The use of a sub-harmonic mixer makes the provision of the LO easier than for fundamental mixers at these frequencies. I and Q mixer outputs are provided and an external 90 degree hybrid is required to select the desired sideband. This device uses Mimix Broadband’s 0.15 μm GaAs PHEMT device model technology, and is based upon electron beam lithography to ensure high repeatability and uniformity. The device comes in a 7x7 mm QFN Surface Mount Laminate Package offering excellent RF and thermal properties and is RoHS compliant. This device is well suited for Millimeter-wave Point-to-Point Radio, LMDS, SATCOM and VSAT applications.

Features
*Sub-harmonic Receiver
*Integrated LNA, LO Buffer, Image Reject Mixer
*7x7 mm, QFN
*+2.0 dBm LO Drive Level
*2.5 dB Noise Figure
*20.0 dB Image Rejection
*100% On-Wafer RF, DC and Noise Figure Testing

XR1006-QD-0N00, XR1006-QD-0N0T, XR1006-QD-EV1

DESCRIPTION
LX1996 is an integrated white LED driver for notebook size displays. It is designed to drive up to six strings of LEDs. The LX1996 consists of a boost converter and six precision current sources. It also includes a direct analog light sensor interface and can be dimmed by a PWM signal or by application of a DC control voltage.
Precision current mirror circuitry sets all channels to the same current with a single programming input. The current value can be programmed up to 30mA per channel with a single resistor from the PRG pin to ground. Channel to channel matching is within ± 0.5 percent typical at 25°C ambient of the channels mean at the rated output current.
Unique design features include temperature compensated LED current, and audible noise reduction using Ultrasonic Pulse Skipping.
Temperature compensated LED current is accomplished by a dedicated input pin (OT) that in conjunction with an external thermistor measures the LED’s ambient temperature and thereby prevents over temperature stress to the LEDs by keeping them within their safe operating area.
Additional features include low sleep mode current (6μA typ.) for extending battery time, multi-mode dimming via ambient light sensor interface, analog dimming, direct PWM dimming and combination of analog and direct PWM dimming for up to a 25000:1 dimming range.
The LX1996 is designed to work over a wide input voltage range from 6V to 28Vdc with adjustable over voltage protection (OVP), and short and open LED protection.
The LX1996 comes in a compact thermal efficient 4x4mm 24pin MLPQ package.

KEY FEATURES
*White LED Backlight Controller for Middle Size Display Panels
*Up to 6 LED Strings with ±0.5% Precision Current Matching
*Wide Input Voltage Range from 6V to 28V
*Temperature Compensated LED Current
*Ultrasonic Pulse Skipping for audible noise reduction
*Direct Ambient Light Sensor Interface for Brightness Control
*High Efficiency over Full Dimming Range
*Low Standby Current
*On-chip Thermal Shut-down
*Over-voltage Protection
*Packaged in a Thermally Efficient 24 pin 4x4mm MLPQ Package

APPLICATIONS
*Notebook & Monitor Displays
*Entertainment Systems
*Automotive Lighting & Panels

LX1996ILQ

Description
The Microchip Technology Inc. MCP601/1R/2/3/4 family of low-power operational amplifiers (op amps) are offered in single (MCP601), single with Chip Select (CS) (MCP603), dual (MCP602), and quad (MCP604) configurations. These op amps utilize an advanced CMOS technology that provides low bias current, highspeed operation, high open-loop gain, and rail-to-rail output swing. This product offering operates with a single supply voltage that can be as low as 2.7V, while drawing 230 μA (typical) of quiescent current per amplifier. In addition, the common mode input voltage range goes 0.3V below ground, making these amplifiers ideal for single-supply operation.
These devices are appropriate for low power, battery operated circuits due to the low quiescent current, for A/D convert driver amplifiers because of their wide bandwidth or for anti-aliasing filters by virtue of their low input bias current.
The MCP601, MCP602, and MCP603 are available in standard 8-lead PDIP, SOIC, and TSSOP packages. The MCP601 and MCP601R are also available in a standard 5-lead SOT-23 package, while the MCP603 is available in a standard 6-lead SOT-23 package.
The MCP604 is offered in standard 14-lead PDIP, SOIC, and TSSOP packages. The MCP601/1R/2/3/4 family is available in the Industrial and Extended temperature ranges and has a power supply range of 2.7V to 6.0V.

Features
*Single-Supply: 2.7V to 6.0V
*Rail-to-Rail Output
*Input Range Includes Ground
*Gain Bandwidth Product: 2.8 MHz (typical)
*Unity-Gain Stable
*Low Quiescent Current: 230 μA/amplifier (typical)
*Chip Select (CS): MCP603 only
*Temperature Ranges:
-Industrial: -40°C to +85°C
-Extended: -40°C to +125°C
*Available in Single, Dual, and Quad

Typical Applications
*Portable Equipment
*A/D Converter Driver
*Photo Diode Pre-amp
*Analog Filters
*Data Acquisition
*Notebooks and PDAs
*Sensor Interface

MCP601R, MCP602, MCP603, MCP604, MCP601-I/P, MCP601-E/SN

General Description
This 8-bit Micro-controller uses a fully static CMOS technology to achieve high speed, small size, low power and high noise immunity.
Internal RC oscillator On chip memory includes 1K words of ROM, and 31 bytes of static RAM.

Features
*Fully CMOS static design
*8-bit data bus
*On chip ROM size :1 K words
*Internal RAM size : 31 bytes (25 general purpose registers, 6 special registers)
*34 single word instructions
*14-bit instructions
*2-level stacks
*Operating voltage : 2.3V ~ 6 V
*Addressing modes include direct, indirect and relative addressing modes
*Power-on Reset
*RC oscillator, and R(160K) is changeable
*12 I/O pins with their own independent direction control

Applications
The application areas of this MDT10C41A1 range from appliance motor control and high speed automotive to low power remote transmitters/receivers, pointing devices, and telecommunications processors, such as Remote controller, small instruments, chargers, toy, automobile and PC peripheral … etc.

MDT10C41A1P, MDT10C41A1S

General Description
The TH72001 FSK transmitter IC is designed for applications in the 315 MHz industrial-scientific-medical (ISM) band. It can also be used for any other system with carrier frequencies ranging from
290 MHz to 350 MHz.
The transmitter's carrier frequency fc is determined by the frequency of the reference crystal fref. The integrated PLL synthesizer ensures that carrier frequencies, ranging from 290 MHz to 350 MHz, can be achieved. This is done by using a crystal with a reference frequency according to: fref = fc/N, where N = 32 is the PLL feedback divider ratio.

Features
*Fully integrated PLL-stabilized VCO
*Frequency range from 290 MHz to 350 MHz
*Single-ended RF output
*FSK through crystal pulling allows modulation from DC to 40 kbit/s
*High FSK deviation possible for wideband data transmission
*Wide power supply range from 1.95 V to 5.5 V
*Very low standby current
*On-chip low voltage detector
*High over-all frequency accuracy
*FSK deviation and center frequency independently adjustable
*Adjustable output power range from -12 dBm to +11 dBm
*Adjustable current consumption from 3.2 mA to 10.3 mA
*Conforms to FCC part 15 and similar standards
*8-pin Small Outline Integrated Circuit (SOIC)

Application Examples
*General digital data transmission
*Tire Pressure Monitoring Systems (TPMS)
*Remote Keyless Entry (RKE)
*Wireless access control
*Alarm and security systems
*Garage door openers
*Remote Controls
*Home and building automation
*Low-power telemetry systems

TH72001KDC

DESCRIPTION
Maxwell Technologies’ 54LVTH162245 devices are 16-bit (dual-octal) non-inverting 3-state transceivers designed for low-voltage (3.3V) VCC operation, but with the capability to provide a TTL interface to a 5V system environment. These devices can be used as two 8-bit transceivers or one 16-bit transceiver. The devices allow data transmission from the A bus to the B bus or form the B bus to the A bus, depending on the logic level at the direction-control (DIR) input. The output enable (OE) input can be used to disable the device so that the buses are effectively isolated. The A-port outputs, which are designed to source or sink up to 12 mA, include equivalent 22-Ωseries resistors to reduce overshoot and undershoot.
Maxwell Technologies' patented RAD-PAK® packaging technology incorporates radiation shielding in the microcircuit package. It eliminates the need for box shielding while providing the required radiation shielding for a lifetime in orbit or space mission. In a GEO orbit, RAD-PAK provides greater than 100 krad (Si) radiation dose tolerance. This product is available with screening up to Class S.

FEATURES
*A-Port outputs have equivalent 22-Ω series resistors, so no external resistors are required
*Support mixed-mode signal operation (5V input and output voltages with 3.3V VCC)
*Support unregulated battery operation down to 2.7V
*TypicalVOLP (output ground bounce) < 0.8V at VCC = 3.3V, TA = 25°C
*IOFF and power-up 3-state support hot insertion
*Bus hold on data inputs eliminates the need for external pullup/pulldown resistors
*Distributed VCC and GND pin configuration minimizes highspeed switching noise
*Flow-through architecture optimizes PCB layout
*Total dose hardness:
-100 krad (Si), depending upon space mission
*Package: 48 pin RAD-PAK® flat pack

54LVTH162245RPFS, 54LVTH162245RPFB, 54LVTH162245RPFE